Philips Vari-Lite VL770 Service Manual Download

Page: 34 / 190

VARI

❋

LITE - VL440 / VL770 / VL880 S

POT

UMINAIRES

ERVICE

ANUAL

1 6

0 2 . 9 6 8 7 . 0 0 1 0 0

Troubleshooting Guide

If a problem is suspected, try recalibrating the luminaire to prompt an error message. Refer to

“Error

Messages” on page 15

for more information. The chart below provides possible causes and remedies

for various error messages and/or symptoms.

Table 2-1: Troubleshooting Guide

Message

Symptom

Description

Possible Cause/Remedy

Lamp
Power
Douse

Lamp does not strike
upon start-up

Lamp Off option is config-
ured

- Reconfigure lamp startup option in Lamp config

menu.

n/a

Lamp douses frequently

Lamp Douse

Fan failure...

- check head and enclosure fans for proper

operation.

Ballast overheating...

- operating within the specified ambient

temperature?

- check enclosure vents for debris / dirt.
- check fan settings in menu.
- check enclosure fans for proper operation.

NOTE: Upon initial power up, ballast fans will run for
a few seconds and then operate as needed.
Enclosure vents must be clear of debris and dirt to
allow proper airflow.

n/a

Lamp will not strike

Lamp Strike Failure

Lamp cutout switch disengaged...

- check lamp cutout switches at lamp box and fan

ducts.

Bad lamp...

- replace lamp.

Low input voltage...

- check input power (must be 100 to 240 VAC).

n/a

Luminaire behaves
oddly

Profile Not Matched

Profile not set correctly...

- check Setup menu for correct type (console patch

/ profile).

n/a

Luminaire does not
power up

No power

Circuit not energized...

- verify circuit breaker (at source) is turned on.

Not plugged in...

- ensure A/C cable is connected to power source.

n/a

Self tests will not run or
software download does
not work from luminaire.

DMX Data Input

Detecting DMX data...

- disconnect DMX input cable.

n/a

No response to DMX
data

DMX Failure

DMX connector disconnected...

- check DMX DATA IN connection.

n/a

Erratic control of lumi-
naire

DMX Termination

No DMX termination or termination not correct...

- check for DMX terminator.

Summary of Contents for Vari-Lite VL770































































































































































































Search results

Summary of Contents for Vari-Lite VL770

Reviews:

Related manuals for Vari-Lite VL770

Brands by name

Popular brands

Philips Vari-Lite VL770, Service Manual

Search results

Summary of Contents for Vari-Lite VL770

Reviews:

Related manuals for Vari-Lite VL770

Brands by name

Popular brands