Philips Vari-Lite VL770 Service Manual Download

Page: 123 / 190

EAD

SSEMBLY

: H

EAD

RAME

SSEMBLY

0 2 . 9 6 8 7 . 0 0 1 0 0

105

Head Assembly

Head Frame Assembly

21.9687.0650 Rev N

Refer to

Figure 3-23

No.

Item

Qty.

UM.

Description

10.9687.0610

AIR DEFLECTOR, DUAL BLOWER (NOTE, PART OF VL770 & VL880 TOP
ASSEMBLIES ONLY - SHOWN FOR REFERENCE ONLY)

10.9678.0674

BRACKET, COVER TETHER

10.9687.0651

PLATE, CHASSIS, FRONT

10.9687.0654

PLATE, CHASSIS, REAR

10.9687.0663

STANDOFF, REFLECTOR BULKHEAD

10.9687.0664

BRACKET, HOMING, FOCUS

10.9687.0667

TRACK, LINEAR ROLLER

10.9687.0684

TRACK, LINEAR ROLLER, TRACKING

10.9687.0685

BRACKET, FRONT COVER SUPPORT

10.9687.0686

BRACKET, CONTROL BOARD

10.9687.0688

BRACKET, DRIVE NUT, FOCUS

10.9687.1617

BRACKET, CABLE MANAGEMENT

10.9687.1661

STANDOFF, POSITION, GOBO MODULE

10.9687.1691

AIR DUCT, LAMP BASE PINCH

10.9687.2616

BRACKET, CABLE MANAGEMENT

21.9687.0632

ASSY, TILT BEARING, LEFT

21.9687.1633

ASSY, TILT BEARING, RIGHT

21.9687.0634

ASSY, ROLLER, LINEAR

21.9687.0652

ASSY, LAMP HOUSING

21.9687.0654

ASSY, BRACKET, UV/IR FILTER

21.9687.0670

ASSY, TILT MOTOR

22.9687.0140

ASSY, FRONT GLASS

24.9687.0700

BOARD ASSY, MAIN CONTROL UNIT (MCU)

24.9687.0701

BOARD ASSY, MOTOR DRIVER PCB

25.9687.0020

SWITCH, SLOTTED OPTICAL

44.9687.0208

MOTOR, SIZE-17, FOCUS

Nut for 44.9687.0208

NUT, LEAD SCREW, FOCUS (NOTE, SUPPLIED WITH 44.9687.0208 ONLY)

Summary of Contents for Vari-Lite VL770































































































































































































Search results

Summary of Contents for Vari-Lite VL770

Reviews:

Related manuals for Vari-Lite VL770

Brands by name

Popular brands

Philips Vari-Lite VL770, Service Manual

Search results

Summary of Contents for Vari-Lite VL770

Reviews:

Related manuals for Vari-Lite VL770

Brands by name

Popular brands