Philips Vari-lite VL3500 Wash FX Luminaries Service Manual Download Page 35

Page: 35 / 194

ROUBLESHOOTING

: T

ROUBLESHOOTING

UIDE

0 2 . 9 6 8 6 . 0 0 1 0 A

Troubleshooting Guide

If a problem is suspected, try recalibrating the luminaire to prompt an error message. Refer to

“Error

Messages” on page 16

for more information. The chart below provides possible causes and remedies

for each message.

Table 2-2: Troubleshooting Guide

Message

Symptom

Description

Possible Cause and Remedy

n/a

No response to DMX

data

DMX Failure

MCB connector disconnected...

- check MCB DATA IN connection.

n/a

Lamp douses frequently

Lamp Douse

Fan failure...

- check fans for proper connection and

operation.

n/a

Lamp will not strike

Lamp Strike Failure

Lamp cutout switch disengaged...

- check lamp cutout switches at lamp box

and fan ducts.

Bad lamp...

- replace lamp.

Low input voltage...

- check input power (must be 200 to 264 VAC)

n/a

Lamp does not strike

upon start-up

Lamp Off option is config-

ured

Reconfigure lamp startup option in Lamp config
menu

n/a

Luminaire behaves

oddly

Profile Not Matched

Profile not set correctly...

- check start DMX address

No Sens

No control, continuous

recalibration, and/or

mechanism at wrong

position

Mechanism failed to find

sensor (reported for Blue,

Amber, Magenta,

ColWheel1, ColWheel2,

CTO, or Aperture)

Motor power not connected...

- connect motor power.

Sensor not connected...

- connect sensor.

Interconnect board not connected securely...

- check connection, inspect for bent pins.

Movement restricted or impeded...

- remove obstruction, check cable routing,

and/or check voltage at MCB test point.

n/a

Luminaire does not

power-up

No power

Switch not turned on...

- verify switch is turned on.

Not plugged in...

- ensure A/C cable is connected to power

source.

Pan/

Encoder/

Fail

Luminaire will not pan

Pan Encoder Failure

MCB pan/tilt connector disconnected...

- connect MCB pan/tilt connector (J8).

Pan motor disconnected

- connect pan motor power.

Encoder faulty...

- replace pan end-of-travel/encoder sensor

assembly.

Summary of Contents for Vari-lite VL3500 Wash FX Luminaries



































































































































































































Search results

Summary of Contents for Vari-lite VL3500 Wash FX Luminaries

Reviews:

Related manuals for Vari-lite VL3500 Wash FX Luminaries

Brands by name

Popular brands

Philips Vari-lite VL3500 Wash FX Luminaries, Service Manual

Search results

Summary of Contents for Vari-lite VL3500 Wash FX Luminaries

Reviews:

Related manuals for Vari-lite VL3500 Wash FX Luminaries

Brands by name

Popular brands