background image

Block Diagrams, Test Point Overviews, and Waveforms

EN 11

LCD CMO 2K7

6.

6.

Block Diagrams, Test Point Overviews, and Waveforms

Not applicable.

7.

Circuit Diagrams and PWB Layouts

Not applicable

8.

Alignments

Not applicable.

9.

Circuit Descriptions, Abbreviation List, and IC Data Sheets

9.1

Circuit Descriptions

Not applicable

9.2

Abbreviation List

AUO

Acer Unipack Optronics (supplier)

CCFL

Cold Cathode Fluorescent Lamp

CMO

Chi Mei Optoelectronics (supplier)

COF

Chip On Flex / Foil / Film

CPT

Chunghwa Picture Tubes (supplier)

DC

Direct Current

FET

Field Effect Transistor

FFC

Flat Foil Cable

FPC

Flexible Printed Circuit

IC

Integrated Circuit

LCD

Liquid Crystal Display

LCM

Liquid Crystal Module

LED

Light Emitting Diode

LPL

LG Philips LCD (supplier)

PCB

Printed Circuit Board (same as PWB)

PSU

Power Supply Unit

PWB

Printed Wiring Board (same as PCB)

RGB

Red, Green, Blue colour space

TCP

Tape Carrier Package

9.3

IC Data Sheets

Not applicable

10. Spare Parts List

Please refer to the Philips Service website, for an actual 
overview (monthly updated).

 
 

11. Revision List

Manual xxxx xxx xxxx.0

First release.

Manual xxxx xxx xxxx.1

Model V470H1-L03 added.

Summary of Contents for V315B1-L05













Reviews: