Philips M3000A Service Manual Download Page 87

Page: 87 / 293

Connecting the Measurement Server...

Installing the Instrument

Switch the Monitor on using the

On-Off/Standby

button:

Making the Altitude Setting

A correct altitude setting is important to ensure accurate CO

readings.

Step 1

Enter Config Mode and press the Setup key.

Step 2

Select Altitude

Step 3

Select the value from the list which is closest to the altitude of the hospital.

Connecting the Measurement Server...

...with the Measurement Server directly on the Monitor

You can connect the Measurement Server to the Monitor by mounting it directly on the
Monitor:

Step 1

Make sure that your Monitor has a link bar:

If your Monitor does not have a link bar:

a. Position the link bar as shown in the diagram above.

Make sure that the guide is in the slot under the plug (which connects to the
Measurement Server).

b. Press the Link Bar into position until it clicks.

Silence

Reset

Suspend

Setup

Main
Screen

On
Off/Standby

AC Power

Battery

On-Off/Standby

Link Bar

Plug to
Measurement Server

Latch

Summary of Contents for M3000A






































































































































































































































































































Search results

Summary of Contents for M3000A

Reviews:

Related manuals for M3000A

Brands by name

Popular brands

Philips M3000A, Service Manual

Search results

Summary of Contents for M3000A

Reviews:

Related manuals for M3000A

Brands by name

Popular brands