manualshive.com logo in svg

Philips M3000A, Service Manual

Share
Download
Philips M3000A Service Manual Download Page 238

Disassembly for the Monitor

222  

Repairing the Instrument

Step 7

Slide out the Power Supply:

 

Removing the Chassis

Read the warnings at the beginning of this chapter.

To remove the chassis, do the following:

Step 1

Remove the Server.

Step 2

Remove the battery.

Step 3

Switch the Instrument on and disconnect the AC power cord from the Instrument 
and the mains power source (after 20 seconds, the capacitors on the Power Supply 
board are drained).

Step 4

Push a thin-bladed screwdriver into the hole next to the cover:

 

Step 5

Release the cover.

Step 6

Prise open the clip on the Server-to-Monitor link bar and slide it off. On newer 
monitors just turn the catch (holding the link bar) into the vertical position:

 

 

Summary of Contents for M3000A






































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands