Philips LPC2101 User Manual Download Page 37 | Manualshive

Page: 37 / 279

background image

© Koninklijke Philips Electronics N.V. 2006. All rights reserved.

User manual

Rev. 01 — 12 January 2006

37

Philips Semiconductors

UM10161

Volume 1

Chapter 3: System control block

3.12 Wake-up timer

The purpose of the wake-up timer is to ensure that the oscillator and other analog
functions required for chip operation are fully functional before the processor is allowed to
execute instructions. This is important at power on, all types of reset, and whenever any of
the aforementioned functions are turned off for any reason. Since the oscillator and other
functions are turned off during Power-down mode, any wake-up of the processor from
Power-down mode makes use of the wake-up timer.

The wake-up timer monitors the crystal oscillator as the means of checking whether it is
safe to begin code execution. When power is applied to the chip, or some event caused
the chip to exit Power-down mode, some time is required for the oscillator to produce a
signal of sufficient amplitude to drive the clock logic. The amount of time depends on
many factors, including the rate of V

DD

ramp (in the case of power on), the type of crystal

and its electrical characteristics (if a quartz crystal is used), as well as any other external
circuitry (e.g. capacitors), and the characteristics of the oscillator itself under the existing
ambient conditions.

Once a clock is detected, the wake-up timer counts 4096 clocks, then enables the on-chip
circuitry to initialize. When the onboard modules initialization is complete, the processor is
released to execute instructions if the external Reset has been deasserted. In the case
where an external clock source is used in the system (as opposed to a crystal connected
to the oscillator pins), the possibility that there could be little or no delay for oscillator
start-up must be considered. The wake-up timer design then ensures that any other
required chip functions will be operational prior to the beginning of program execution.

Any of the various Resets can bring the microcontroller out of Power-down mode, as can
the external interrupts EINT2:0 and the RTC interrupt if the RTC is operating from its own
oscillator on the RTCX1-2 pins. When one of these interrupts is enabled for wake-up and
its selected event occurs, an oscillator wake-up cycle is started. The actual interrupt (if
any) occurs after the wake-up timer expires, and is handled by the Vectored Interrupt
Controller.

However, the pin multiplexing on the LPC2101/02/03 (see

Section 6.2 on page 61

Section 7.4 on page 66

) was designed to allow other peripherals to bring the device out of

Power-down mode. The pin-function pairing allows interrupts from events relating to RI1 /
EINT2.

Fig 11. APB divider connections

PLL0

crystal oscillator or

external clock source

(F

OSC

)

APB DIVIDER

processor clock

(CCLK)

APB clock

(PCLK)

«
...
35
36
37
38
39
...
»

Summary of Contents for LPC2101
























































































































































































































































































Reviews:

No comments

Related manuals for LPC2101

Brand: Aalborg Pages: 128

Brand: Paoli Pages: 16

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Hanbay Pages: 18

Brand: Kamstrup Pages: 36

Brand: Kantronics Pages: 201

Sundstrom SR307

Brand: S.E.A. Group Pages: 5

Brand: Cypress Semiconductor Pages: 36

Brand: L&L KILNS Pages: 12

Brand: InnoMedia Pages: 10

Brand: SAES Pages: 36

ARES-1231 Series

Brand: Arbor Technology Pages: 94

Brand: Salus Pages: 24

Brand: Herth+Buss Pages: 31

Brand: Eaton Pages: 9

Brand: Watt Stopper Pages: 3

WaveLinx Wired ILM-SCMA0401-2

Brand: Cooper Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands