Philips Faro 770 Series Extended User Documentation Download Page 10

Page: 10 / 51

Install the handset

The batteries are pre-installed in the
handset. Pull the battery tape off from
the battery door before charging.

Caution

•

Risk of explosion! Keep batteries away from
heat, sunshine or fire. Never discard batteries
in fire.

•

Use only the supplied batteries.

•

Risk of decreased battery life! Never mix
different brands or types of batteries.

Note

•

Charge the batteries for 8 hours before first
use.

•

If the handset becomes warm when the
batteries are being charged, it is normal.

Warning

•

When replacing the batteries, check the
battery polarity. Incorrect polarity may
damage the product.

Configure your phone

(country dependent)

When using your phone for the first
time, you see a welcome message.

Press

[OK]

Set the country/language

Select your country/language, then
press

[OK]

to confirm.

The country/language setting is
saved.

Note

•

The country/language setting option is
country dependent. If no welcome message
is displayed, it means the country/language
setting is preset for your country. Then you
can set the date and time.

To reset the language, see the
following steps.

Select

[Phone setup]

[Language]

then press

[OK]

to confirm.

Select a language, then press

[OK]

to confirm.

The setting is saved.

Summary of Contents for Faro 770 Series




















































Search results

Summary of Contents for Faro 770 Series

Reviews:

Related manuals for Faro 770 Series

Brands by name

Popular brands

Philips Faro 770 Series, Extended User Documentation

Search results

Summary of Contents for Faro 770 Series

Reviews:

Related manuals for Faro 770 Series

Brands by name

Popular brands