Philips DVD755VR Service Manual Download Page 44

Page: 44 / 154

3-15

5. Hi-Fi CIRCUIT

(A) No Sound(EE Mode)

YES

No Sound.

Check the TU Audio of IC801
Pins2, 3.

Check the DVD Audio of IC801
Pins4, 5.

Check the AV1 Audio of IC801
Pins6, 7.

Check the AV2 Audio of IC801
Pins8, 9.

Check the AV3 Audio of IC801
Pins10, 11.

Check the Vcc of IC801 Pins34, 40,
IC802 Pin4.

YES

Check the IIC Clock and DATA at
IC801 Pins42, 43, IC802 Pins32, 33.

YES

Check the Audio of IC801 Pins16, 17.

YES

Check the Audio of IC802 Pins22, 26.

YES

Check the JK902.

Check the IC751 Pins30, 31.

Check the DVD MODULE.
(PMD02 Pins13, 15).

Check the Scart1 Jack.
(SC901 Scart1 Audio in Pins2, 6).

Check the front Jack.
(L5F1, L5F2).

Check the Scart2 Jack.
(SC901 Scart2 Audio in Pins2, 6).

Check the Power 5.2V, 12VT.

YES

Check the IC501 Pins59, 60.

Replace IC801.

Replace IC802.

Summary of Contents for DVD755VR



























































































































































Search results

Summary of Contents for DVD755VR

Reviews:

Philips DVD755VR, Service Manual, Page: 44 / 154

Search results

Summary of Contents for DVD755VR

Reviews: