Philips DVD755VR Service Manual Download Page 40

Page: 40 / 154

3-11

4. Y/C CIRCUIT

(1) No Video in EE Mode,

No Video in EE Mode

Check the 24Pin of Tuner.

Does the Video signal
appear at the IC301 Pin48?

Is 5V applied to the IC301
Pins18, 24, 42, 55, 72, 91?

Does the Video signal
appear at the IC301 Pin65?

Does the Video signal
appear at the IC501 Pin19?

Does the Video signal
appear at the Emitter termi-
nal of the Q307, Q308?

Check the 5.2VT, 5.3VA
Line. (Power Circuit)

Is I

C BUS signal applied to

the IC301 Pins68, 69?

Check C316. (AGC)

Chck the path of the signal
between the IC301 Pin65
and IC501 Pin17.

Replace the IC301.

Does the 12VT, 5.4VA
appear at the Emitter termi-
nal of the Q804, Q308.

Replace the Q804, Q308.

Check the 12VT, 5.4VA
Line. (Power Circuit)

Check the System Circuit.
(Refer to ‘SYSTEM I

C BUS

CHECK Trouble Shooting’)

YES

Summary of Contents for DVD755VR



























































































































































Search results

Summary of Contents for DVD755VR

Reviews:

Philips DVD755VR, Service Manual, Page: 40 / 154

Search results

Summary of Contents for DVD755VR

Reviews: