OccuSwitch DALI
User Guide
Page 36
4.3
Reset to factory defaults
The OccuSwitch DALI system can be set to default factory
settings (out of the box settings) using the
IRT9090 .
1 Press the
Reset
button .
The LED on the transmitter starts to
blink .
2 Point the remote towards the
OccuSwitch DALI and press the green
Send
button .
The luminaires will flash once to confirm
the reset (see also note) .
B
Warning
Reset to factory defaults will only reset the
following parameters:
• Application mode (default: 1)
• 100h burn-in mode (default: off)
• Power up state (default: on)
• Background level (default: 20%)
• IR group (default: A)
• DALI groups of all connected luminaires (OccuSwitch
DALI will work in un-commissioned mode)
Depending from which mode the reset to factory is
done and whether there is a parallel linking connection
or not, there are different behaviors after conformation
blinking of lamps . In some modes the lamps stays off
after conformation blink, in other modes the lamps go
back on a few seconds after conformation blinking of
lamps . To make sure that changes are implemented
correctly it is advised to restart the device after a reset
to factory defaults . Please be aware that Groups, that
are created according to chapter 5 .8, are not removed
with this Reset to factory defaults and thus Parallel
Link is not active .
4.4
Walk test
To check that the OccuSwitch DALI system is correctly
installed and commissioned, the OccuSwitch DALI system
can be set into the walk test mode . In this mode, all
actions of the OccuSwitch DALI run at a high speed (10
times faster than normal), movement detection period is
set to 30 seconds (independent of potentiometer settings),
and daylight dependent switching and daylight override
are disabled .
The walk test mode can be started and stopped using the
IRT9090 tool .
Entering the walk test mode
1 Point the remote towards the
OccuSwitch DALI and press
Test
to enter
the walk test mode .
The LEDs on the OccuSwitch DALI will start
running a color sequence .
Leaving the walk test mode
1 Point the remote towards the
OccuSwitch DALI and press
Test
to leave
the walk test mode .
The luminaires will flash twice to confirm
the end of walk test mode .
The OccuSwitch DALI returns to normal
operation .
D
Note
After one hour of being in the walk test mode, the
OccuSwitch DALI will automatically return to normal
operation . In this case it also flashes the luminaires
twice .
70% G
min
100 h
group
link?
mode?
mode
power up background IR group
reset
add
pir
delay
daylight RF channel
0
0
off
save
on
I/II
O)))
A-G
zone
%
on/off
8
7
9
50% E
40% D
60% F
5
4
6
20% B
10% A
II
30% C
PL
BMS
W/C
2
1
3
test
config
scene
70% G
min
100 h
group
link?
mode?
mode
power up background IR group
reset
add
pir
delay
daylight RF channel
0
0
off
save
on
I/II
O)))
A-G
zone
%
on/off
8
7
9
50% E
40% D
60% F
5
4
6
20% B
10% A
II
30% C
PL
BMS
W/C
2
1
3
test
config
scene
70% G
min
100 h
group
link?
mode?
mode
power up background IR group
reset
add
pir
delay
daylight RF channel
0
0
off
save
on
I/II
O)))
A-G
zone
%
on/off
8
7
9
50% E
40% D
60% F
5
4
6
20% B
10% A
II
30% C
PL
BMS
W/C
2
1
3
test
config
scene
