Alignments
EN 101
EJ2.0U LA
8.
8.4
Option Settings
8.4.1
Introduction
The microprocessor communicates with a large number of I
2
C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these specific
ICs (or functions) is made known via the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC
before
the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
•
The new option setting is only active after the TV is
switched "off" and "on" again with the Mains switch (the
NVM is then read again).
8.4.2
Dealer Options
Table 8-3 Dealer options
8.4.3
(Service) Options
Select the sub menu's to set the initialization codes (options).
Table 8-4 Options
8.4.4
Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set.
Example:
The options sticker gives the following option
numbers (depending on the model):
•
00016 00006 00033 14979
•
01035 00000 04768 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicates software options 5 to 8.
Menu item
Subjects
Options
Description
Personal Options
Picture Mute
On
Picture mute active in case no picture detected
Off
Noise in case of no picture detected
Virgin Mode
On
TV starts up (once) with a language selection menu after the Mains switch is turned "on" for the first time (virgin mode)
Off
TV does not start up (once) with a language selection menu after the Mains switch is turned "on" for the first time (virgin
mode)
2CS Korea (only for AP
region)
Off
Self learning TV
Off
Menu-item
Subjects
Options
Description
PIP/DS
Dual Screen
One tuner dual screen
DS with one tuner
Data
EPG
Off
Feature not present
RRT
Yes / No
Parental control is enabled via the Regional Rating Table (RRT)
Display
Screen
“Value”
Used screen size, type, and resolution (see table “Display code overview” in chapter “Service
Modes”for the values)
Scanning Backlight
On / Off
Feature present / not present
Dimming Backlight
On / Off
Feature present / not present
Video Repro
Picture Processing
No Spider
Feature not present
Combfilter
None / 2D / 3D
Only selectable with Columbus in set: No/without RAM/with RAM
Ambient Light
Off / Stereo
Off / Two inverters stereo
MOP
On / Off
Feature present / not present (for sets with AmbiLight this is “on”)
POD
Off
no POD implemented
Source Selection
HDMI 1
None
No HDMI
With analogue audio
DVI
Without analogue audio
HDMI
HDMI 2
None
No HDMI
USB version
1.1
USB 1.1 in side I/O panel
IEEE1394
Not present
Connector not present
Ethernet
Off
Connector not present
SPDIF inputs
None
No connector present
Audio Repro
Subw. Internal Present
Yes / No
Internal sub woofer present / not present
Acoustic System (Cabinet design,
used for setting dynamic audio
parameters).
None
n.a.
Others
n.a.
ME6 2K6
for this set
Miscellaneous
Alternative Tuner
Philips
Tuner brand
Tuner Type
TD1336S
Tuner type
Hotel mode
Off
Opt. no.
Group 1
xxxxx xxxxx xxxxx xxxxx (see set sticker)
Group 2
xxxxx xxxxx xxxxx xxxxx (see set sticker)
Store
