Phase3 Chipmunk 370 Operating Instructions Manual Download Page 1 | Manualshive

Page: 1 / 16

Phase3 Chipmunk 370 Operating Instructions Manual Download Page 1

1

✦

✦

✦

✦

✦

IMPORTANT

✦

✦

✦

✦

✦

Before beginning assembly, please read and understand the warnings listed on the next page. Failure to

read and understand these warnings could lead to bodily harm and/or injury. The Phase3 Models Chipmunk 370 is not
intended for those under 14 years of age, unless closely supervised by an adult.

O P E R A T I N G I N S T R U C T I O N S

SPECIFICATIONS AND FEATURES:

●

Wing Span:

32 Inches (813mm)

●

Wing Area:

190 Square Inches (12.25dm

2

)

●

Length:

25 Inches (635mm)

●

Weight RTF:

12.5 Ounces (354gr)

●

Wing Loading:

9.5 Ounces Per Square Foot (29gr/dm

2

)

●

4-Channel Full-House Functions for Air Show-Style Aerobatics

●

Factory-Built and Finished with All Electronics Installed

●

Molded Foam Fuselage with Laminated Surfaces for Durability

●

Lightweight, One-Piece Wing

●

Detailed Factory-Applied Color Scheme

●

7.2 Volt 600mAH AAA NiMH Battery

●

AC Charger and 12V DC Fast-Charger

●

Direct Drive 370 Motor with Propeller

●

Easy-to-Access Magnetic Hatch Cover for Battery

Includes 8.4 Volt 600mAH NiMH Battery, AC Charger,

12V DC Fast-Charger and More!

All contents copyright © 2005, Phase3 Models

Version V2.0 January 2006

Kit Product Number: 107110

Inspired by air shows around the world, the Phase3 Models Chipmunk 370 offers spirited performance for intermediate and advanced
pilots. This 4-channel aerobatic aircraft doesn't need big areas to fly, and will still put on a big-time show with its beautiful colors and
advanced performance. Frankly, you'll be impressed by what a lightweight, foam molded aircraft with a 370 motor can do! The high-rpm,
5-inch diameter prop pulls the Chipmunk 370 along at a good speed, giving you the power and authority for most air show-style aerobatics.

Molded from tough, lightweight skinned foam, the fuselage is light and strong. The wing is hollow-core shaped foam with an internal
spar that offers the strength and light weight needed for high performance aircraft. The Chipmunk 370 is easy to finish, too. The
wing is one piece, and the stabilizer is factory-installed along with all the electronics. Even the color scheme is applied. You simply
bolt on the vertical stabilizer, charge the battery, install the wing, and you're ready to fly. The Phase3 Models Chipmunk 370 even has
an easy-access battery hatch retained with magnets, so changing the battery is fast and hassle-free.

✦

✦

✦

✦

✦

CAUTION

✦

✦

✦

✦

✦

The Phase3 Models Chipmunk 370 is designed

for intermediate to advanced pilots. It's not intended for
beginner pilots. It is not a trainer!

Phase3 Models

P.O. Box No. 74282

Kowloon Central, Hong Kong, China

1
2
3
...
»

Summary of Contents for Chipmunk 370

















Reviews:

No comments