Thank you for your purchase of the
SC7000 high-performance desoldering tool as one of your
service
We hope that the use of our quality product will give you satisfaction for years to come. To get the
maximum performance
instrument we suggest
that
the following instructions before operating
the tool. This basic technical Sheet will help you to
understand the features. advantages. and maintenance
necessary to keep your instrument
efficiently.
4.
5.
6.
Plug the power cord into an electrical outlet. Then set power switch, located on the bottom handgrip,
“ON” position and allow instrument to warm up for a few minutes.
a) When instrument is operated the first time fumes may develop in the area of the heater holder. This
is normal and is caused by the protective coating burning off of the healing element.
Check the filter cartridge proper position and direction.
Set the temperature control knob to Suit the application. for standard desoldering procedures, it is advisable
to choose a position between
and
when working on
applications the most
satisfactory results will be obtained at temperatures ranging from
to
T
O
the solder around any lead-wire of a given components. simply place the bore of the desoldering
tip
the wire-end, insert and at the time the solder around it melts, gently pull the
trigger
switch to allow the pump suck the molten compound away.
The removed Solder will gradually accumulate in the filter cartridge and may be
with tweezers,
when the felt in the filter cartridge becomes dirty the suction effect of the system
decrease. it is
recommended that the filter cartridge be changed when between
and one-half of the filter
a build up of impurities.
If the
of the desoldering tip becomes clogged with flux and/or solder and causes a decrease in suction
performance it is necessary then to
the channel in a
condition. using the cleaning pin set.
Note:
The instrument is delivered with a cleaning pin composed of 3 different pin
be used
to desoldering tip sizes. Each Size has a long and a
pin. Use the short pin first, then
followed by the
longer
pin.
After a working session, clear the bore any flux
solder residuals after that. set the operating mode
to the hot-air-blow position and clear tip completely. Your tool will
be ready to proceed with your
The hooking hole may be used to hang the
in a counter weighted position for permanent desoldering
As you are aware. the unique design of the SC-7000
tool allows for the quick conversion from
removal HOT-AIR Blower. By using the hot-air blower with the
accessory kit
easily removed from
and substrates. The change hot-air blower requires:
a)
the desoldering tip and replace with hat-air
using wench supplied.
Replace the desoldering cartridge with the special hot-air cartridge.
Set the vacuum/hot-air
to hot-air blower position.
The hot-air flow rate can be adjusted with the switch lever.
Depending on the nature the desoldering work and the
of the component. the temperature
should be set at the appropriate level.
CAUTION:
Take care when using the hot-air blower function. The operator should be aware that the
-AIR” can cause serious burns.
Hot-Air
Hot-Air Cartridge
Wire Holder.
Stainless
Blade Holder ST-705
For use on
Used hot-air desoldering applications
Stainless steel wire holder
a
or SOP”’
Stainless
blade
holder Used
d:
Never attempt wash or rinse a dirty filter in any kind volatile Solvent. as this may decrease the
of the instrument and may
an explosive hazard.
To avoid damage to heating element (from thermal shock)
use waler or any other coolant on
section or tip.
Excessive
and vibration the instrument itself may also damage the heating element.
extended use, flux may accumulated on the valve sheet, gasket
the
Silicon
the vacuum pump lowering its suction performance. Periodic maintenance and cleaning of these part:
advisable, any flawed or deformed parts should be replaced.
The desoldering
should be used in
with your instrument. This particular
has been designed to maximize the performance and life of your SC7000 desoldering tool.
2
