background image

 

 

VersiStart i III 

44 

 

2D – Start Ramp Time 

Range: 

1 - 180 (seconds) 

Default: 

10 seconds 

Description:  Sets the total start time for an Adaptive Control start or the ramp time for current ramp starting (from the initial current to 

the current limit). 

 

2E – Kickstart Level 

Range: 

100% - 700% FLC 

Default: 

500% 

Description:  Sets the level of the kickstart current. 

 

2F – Kickstart Time 

Range: 

0 – 2000 milliseconds 

Default: 

0000 milliseconds 

Description:  Sets the kickstart duration.    A setting of 0 disables kickstart. 

 

 

CAUTION 
Kickstart subjects the mechanical equipment to increased torque levels.    Ensure the motor, load and couplings can handle 
the additional torque before using this feature. 

 

2G – Excess Start Time 

Excess start time is the maximum time the VersiStart i III will attempt to start the motor.    If the motor does not transition to Run mode 
within the programmed limit, the starter will trip.    Set for a period slightly longer than required for a normal healthy start. A setting of 0 
disables excess start time protection. 

Range: 

0:00 - 4:00 (minutes:seconds) 

Default: 

20 seconds 

Description:  Set as required. 

 

2H – Stop Mode 

Options: 

Coast To Stop (default) 
TVR Soft Stop 
Adaptive Control 

Brake 

Description:  Selects the stop mode. 

 

2I – Stop Time 

Range: 

0:00 - 4:00 (minutes:seconds) 

Default: 

0 second 

Description:  Sets the time for soft stopping the motor using timed voltage ramp or Adaptive Control. This also sets the total stopping 

time when using brake. 
If a main contactor is installed, the contactor must remain closed until the end of the stop time. Use a programmable 

output configured to Run to control the main contactor. 

 

2J – Adaptive Start Profile 

Options: 

Early Acceleration 
Constant Acceleration (default) 

Late Acceleration 

Description:  Selects which profile the VersiStart i III will use for an Adaptive Control soft start. 

 

2K – Adaptive Stop Profile 

Options: 

Early Deceleration 
Constant Deceleration (default) 

Late Deceleration 

Description:  Selects which profile the VersiStart i III will use for an Adaptive Control soft stop. 

 

 

Summary of Contents for VersiStart i III












































































Reviews: