background image

Copyright Statement

This document must not be reproduced in any way whatsoever, either printed or electronically, without 
the consent of:

Perle Systems Limited

 

60 Renfrew Drive

 

Markham, ON

 

Canada 

 

L3R 0E1

Perle reserves the right to make changes without further notice, to any products to improve reliability, 
function, or design.

Perle, the Perle logo, and MCR1900 are trademarks of Perle Systems Limited.

Perle Systems Limited, 2010.

FCC

This product has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of 
the FCC rules. These limits are designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions in this 
Guide, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference, in which case the user will be required to correct 
the interference at his/her own expense.

EN 55022, Class A,

WARNING: This is a Class A product. In a domestic environment this product may cause radio 
interference in which case the user may be required to take adequate measures.

EN 55024, Class A,

Summary of Contents for MCR1900


























Reviews: