Perle IDS-300 Hardware Installation Manual Download Page 5 | Manualshive

Page: 5 / 26

background image

3

IDS-305G Hardware Installation Guide

Overview

This chapter discusses the following topics:

• LED Indicators

• Switch Model View

• Ports

• Port Status Indicators

The table below gives a brief overview of the models covered in this guide. For more details and for the

most up-to-date list of models, please refer to the product pages at www.perle.com.

Note:

xxxxxx denotes the specific type of fiber port installed. Refer to the Perle Website for up to date

details on the available options.

Standard Models

Port 1-4

Port 5

Temp

IDS-305G-XXXXXX

10/100/1000Base-T (RJ45)

1000Base-X SC/ST fiber

Standard

IDS-305G-XXXXXX-XT

10/100/1000Base-T (RJ45)

1000Base-X SC/ST fiber

Industrial

«
...
3
4
5
6
7
...
»

Summary of Contents for IDS-300



























Reviews:

No comments

Related manuals for IDS-300

Brand: S&C Pages: 26

Brand: S&C Pages: 37

Brand: S&C Pages: 28

Brand: D-Link Pages: 2

TNS5500D Series

Brand: 3onedata Pages: 5

IPS7112G-4GS-8GPOE

Brand: 3onedata Pages: 3

Brand: CAME Pages: 2

Brand: DITEC Pages: 8

Pow-R-Line SPX0361126

Brand: Eaton Pages: 584

Brand: NETGEAR Pages: 8

Brand: Eaton Pages: 2

Brand: Ubiquiti Pages: 14

Brand: LEGRAND Pages: 4

Brand: Advantech Pages: 28

Brand: SMART-AVI Pages: 2

Brand: Control 4 Pages: 2

Brand: I-Rocks Pages: 18

Brand: Keysight Technologies Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands