Perkins 403C-11 Workshop Manual Download Page 80

Page: 80 / 128

Workshop Manual, TPD 1458E, issue 3 - Perkins Confidential: Green

400 Series

To check the timing of the fuel injection pump

Operation 8-2

1 Set the piston for number one cylinder to TDC on the compression stroke. Turn the crankshaft counter
clockwise a quarter of a revolution.

2 Remove the ESOS, high pressure fuel pipes and low pressure fuel pipes from the fuel injection pump.

3 Ensure that the fuel pump rack is in the maximum fuel position.

4 Remove the delivery valve holder for number 1 cylinder and remove the delivery valve. Store the delivery
valve in clean fuel until assembly.

Note: The fuel pump may have to be removed to an upright position to remove and to fit the delivery valves.

5 Connect the fuel pump spill pipe (1) to the delivery valve holder for number 1 cylinder.

Continued

Engine

Special tools

Part number

All models

Spill pipe

21825680

H1086

Summary of Contents for 403C-11

































































































































Search results

Summary of Contents for 403C-11

Reviews:

Perkins 403C-11, Workshop Manual, Page: 80 / 128

Search results

Summary of Contents for 403C-11

Reviews: