PerkinElmer CLARUS 590 GC User Manual Download Page 36

Page: 36 / 284

36 . Clarus 590 GC User’s Guide

Isothermal Program

If the program is isothermal, the temperature of the injector is held constant for the duration of the run.

Changes entered in the field take effect immediately.

Carrier Gas Program

The Carrier Gas options for PSSI include

Pressure

Flow

, or

Velocity

. If the option for

Cap

control is

selected, you can program the carrier gas according to one of the three values. The corresponding actual

values for the other units appear as read-only text on the screen. Touching the program button next to

the field displays the associated program for the entry field value.

Pressure

The carrier gas is configured for

Pressure

. This option appears in the entry field. Touching the

Program

button in the

Active Method

displays the

Carrier Pressure Program

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands