manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 26

26 . Clarus 590 GC User’s Guide

 

 

Non-installed Devices 

If a device is not installed, a grayed out deactivated button with no indicator light appears in the 

designated position.  

 

Touching the button prompts the following dialog box: 

 

Run Button 

 

The Run icon displays the Manual injection and Autosampler settings if the device is enabled. The bottom 

bar on these screens includes the Start button. When the system is running, the Start button changes to 

the Stop button. Since the Start button is only available on the Autosampler and Manual inject screens, 

you must initiate a run from these screens. However, when the system is running, the Stop button 

appears on all screens allowing you to Stop the run from anywhere in the application. If the system is 

Paused, the Resume button appears on all screens.  

Autosampler 

When an Autosampler is enabled, the Run button defaults to that screen. The following screens shows 

the enable check box on the configuration screen and the associated Autosampler screen in the Active 

Method. 

 

When the instrument is ready, touch the 

Start 

button to begin the run. If you touch Start before the 

system is ready, the run will start when the system reaches the ready status. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands