background image

09931528A 

 

 

PerkinElmer, 710 Bridgeport Avenue,  

Shelton, CT 06484-4794, U.S.A

 

Produced in the USA.

 

 

FL 6500/ 8500 Microplate Reader Installation Instructions  

This instruction sheet describes the installation of this accessory which is used with the FL 6500/8500 

Fluorescence Spectrometer. 

NOTE:  

Read these instructions before you install this accessory. 

Contacting PerkinElmer 

Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part 

numbers. 
See our website: 
http://perkinelmer.com 
PerkinElmer's catalog service offers a full selection of high-quality supplies. 
To place an order for supplies and many replacement parts, request a free catalog, or ask for information: 
If you are located within the U.S., call toll free 1-800-762-4000, 8 a.m. to 8 p.m. EST. Your order will be 

shipped promptly, usually within 24 hours.  
If you are located outside of the U.S., call your local PerkinElmer sales or service office. 

Features 

• Plug-n-play accessory 
• Measure samples in any plate format (Default: 96 or 384 well) 
• Create new plate formats graphically and interactively 

   

Figure 1 Microplate Reader and cover (P/N: N4201024) 

Summary of Contents for FL 6500



















Reviews: