DIGISAT PLUS
Operation and Maintenance
DG-2 Plus
Open the Velcro flap and remove the DC power plug.
Close the Velcro flap.
Insert the small female plug from the battery pack into
the input connector on the bottom of the DIGISAT.
Turn the DIGISAT
ON
by pressing the power button one
time.
After tracking the satellite antenna, press & hold the
power button to turn the DIGISAT battery pack
OFF
.
The DIGISAT can operate one LNBF (dual port type) up
to two hours on a single charge.
Plug either AC or DC charger into the male pigtail connector. From a
fully discharged state, the AC charger will charge the 400 mA
battery pack in about 12 hours. Do not continue charging with
the wall charger beyond that time. The DC charger will charge
the battery pack fully in 2 to 4 hours.
1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and
connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT.
2) Turn the DIGISAT on as illustrated above.
3) The audible squawker circuit can be turned ON by pressing the left and right yellow
buttons simultaneously.
DIGISAT PLUS
Operation and Maintenance
DG-2 Plus
Open the Velcro flap and remove the DC power plug.
Close the Velcro flap.
Insert the small female plug from the battery pack into
the input connector on the bottom of the DIGISAT.
Turn the DIGISAT
ON
by pressing the power button one
time.
After tracking the satellite antenna, press & hold the
power button to turn the DIGISAT battery pack
OFF
.
The DIGISAT can operate one LNBF (dual port type) up
to two hours on a single charge.
Plug either AC or DC charger into the male pigtail connector. From a
fully discharged state, the AC charger will charge the 400 mA
battery pack in about 12 hours. Do not continue charging with
the wall charger beyond that time. The DC charger will charge
the battery pack fully in 2 to 4 hours.
1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and
connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT.
2) Turn the DIGISAT on as illustrated above.
3) The audible squawker circuit can be turned ON by pressing the left and right yellow
buttons simultaneously.
Velcr
o Pa
d
DIGISAT PLUS
Operation and Maintenance
DG-2 Plus
Open the Velcro flap and remove the DC power plug.
Close the Velcro flap.
Insert the small female plug from the battery pack into
the input connector on the bottom of the DIGISAT.
Turn the DIGISAT
ON
by pressing the power button one
time.
After tracking the satellite antenna, press & hold the
power button to turn the DIGISAT battery pack
OFF
.
The DIGISAT can operate one LNBF (dual port type) up
to two hours on a single charge.
Plug either AC or DC charger into the male pigtail connector. From a
fully discharged state, the AC charger will charge the 400 mA
battery pack in about 12 hours. Do not continue charging with
the wall charger beyond that time. The DC charger will charge
the battery pack fully in 2 to 4 hours.
1) Attach the short coax cable jumper supplied with this kit to your LNBF (or LNB) and
connect other end of the coax cable jumper to the TOP "F" connector of the DIGISAT.
2) Turn the DIGISAT on as illustrated above.
3) The audible squawker circuit can be turned ON by pressing the left and right yellow
buttons simultaneously.
Velcr
o Pa
d
Velcr
o Pa
d
TURNING THE UNIT
ON
CHARGING THE BATTERY PACK
SIMPLIFIED OPERATING INSTRUCTIONS
Plug into 110vAC wall
outlet socket. A discharged
pack can be fully restored
in about 12 hours. DO NOT
leave the pack connected to
the AC charger indefinitely.
Plug into 12vDC (auto lighter) or accessory socket.
DO NOT continue DC charging beyond 4 hours.
PERFECT 10
PERFECT 10
Satellite Distributing
Satellite Distributing
Ds/manuals/perfect/digisat/digi07
Ver 1.6
DC Power
Plug
continued on back
