5
RSS260 AS
Operating instructions
Safety sensor
EN
12
12
16
15
18
12
18
Mounting set
• Ordering code 103005469
• Alternative use of the mounting plates or ferrules
• Mounting plates: 2 pieces for mounting on non-linear stable basis,
e.g. on groove rails/profiles
• Ferrules: 4 pieces for insertion to secure the screw fixings to the
mounting surface for applications with regular high temperature
variations
4. Electrical connection
4.1 General information for electrical connection
The electrical connection may only be carried out by
authorised personnel in a de-energised condition.
The connection to the AS-Interface system is realised through an M8
or M12 connector. The connectors are A-coded. The connection to
the M12-plug is made (according to EN 62026-2) to the AS-Interface
systems with an adapter cable of M8 / 4-pin (socket) on to M12 / 4-pin
(plug):
Pin assignment M8 / M12 connector
spare
3
2
1
4
AS-i -
AS-i +
spare
Connector adapter cables (available as accessories)
IP67, M8-coupling to M12-connector, 4-pin
Cable length
Ordering code
1 m
103003648
2 m
103003649
3 m
103003651
5. Functions and configuration
5.1 Programming the slave address
The slave address is programmed through the M8 connector. Any
address from 1 to 31 can be set by means of the AS-i bus master or a
hand-held programming device.
5.2 Configuration of the safety monitor
The RSS260 AS can be configured in the ASIMON configuration
software with the following monitoring devices (also refer to the
ASIMON manual). (also refer to the ASIMON manual)
Double channel dependent
• Synchronisation time: 0.1 s
• Optionally with startup test
• Optional with local acknowledge
The configuration of the safety monitor must be tested and
confirmed by a qualified and authorised safety expert/safety
engineer.
5.3 Status signal "safety release"
The "safety release" status signal from a Safety at Work slave can be
cyclically queried by the control system through the AS-i master. To
thiseffect, the 4 input bits with the varying SaW code of a Safety at
Work slave are evaluated through an OR operation with 4 inputs in the
control system.
5.4 Actuator teaching / actuator detection
Safety sensors with standard coding are ready to use upon delivery.
Individually coded safety sensors and actuators will require the
following "teach-in" procedure:
1. Switch the safety sensor's voltage supply off and back on.
2. Introduce the actuator in the detection range. The teach-in procedure is
signalled at the safety sensor, yellow LED flashes (1 Hz).
3. After 10 seconds, brief cyclic flashes (3 Hz) request the switch-off
of the operating voltage of the safety sensor. (If the voltage is not
switched off within 5 minutes, the safety sensor cancels the "teach-
in" procedure and signals a false actuator by 5 yellow flashes.)
4. After the operating voltage is switched back on, the actuator must be
detected once more in order to activate the taught actuator code. In
this way, the activated code is definitively saved!
For ordering suffix -I1, the thus executed allocation of safety sensor and
actuator is irreversible.
For ordering suffix -I2, the "teach-in" procedure for a new actuator can be
repeated an unlimited number of times . When a new actuator is taught,
the code, which was applicable until the moment, becomes invalid.
Subsequent to that, an enabling inhibit will be active for ten minutes, thus
providing for an increased protection against tampering. The AS-i Duo
LED will flash red/green until the expiration of the time of the enabling
inhibit and the detection of the new actuator. In case of power failure
during the lapse of time, the 10-minutes tampering protection time will
restart.
Actuator detection (AD)
Device with actuator detection (AD) can emit the number of especially
coded actuators through the parameter port.
In this way, a non-safe identification of the actuator is possible.
Through the 4 bits of the parameter port, the actuators with the
numbers 01 - 15 can be detected and transmitted to the control.
If no actuator is detected, a 0 will be emitted.
Safety sensors and actuators with actuator detection must always be
used in pairs.
Actuator RST260-1-AD01…15, 15 different actuators at the most