manualshive.com logo in svg

Pepperl+Fuchs IC-KP-B7-V95, Manual

Share
Download
Pepperl+Fuchs IC-KP-B7-V95 Manual Download Page 56

 20

13

-0

4

56

IC-KP-B7-V95

Commands

Set tag ID code (TI)

Command:

Response:

This command restricts the execution of all other read/write commands to the 

read/write tag with the specified ID code. This also applies if another read/write 

tag is located within the detection range. A targeted response is achieved from the 

read/write tag as a result.

<ByteNum> = 0h: Do not make a selection. An ID code is not specified in the 

telegram.

<ByteNum> = 8h (System IQ): Make a selection. An ID code must be specified in 

the telegram.

<ByteNum> = 0h deletes this filter.

Byte

Content

Bit no.

7

6

5

4

3

2

1

0

Byte 0

Command code (BCh)

1

0

1

1

1

1

0

0

Byte 1

ID length/Channel/Toggle bit

<ByteNum>

<Channel>

<T>

Byte 2

Data

<ID code>

Byte 3

Data

<ID code>

Byte 4

Data

<ID code>

Byte 5

Data

<ID code>

Byte

Content

Bit no.

7

6

5

4

3

2

1

0

Byte 0

Command code (BCh)

1

0

1

1

1

1

0

0

Byte 1

Reserved/Channel/Toggle bit

<ByteNum>

<Channel>

<T>

Byte 2

Status

<Status>

Byte 3

Reply counter

<ReplyCounter>

Note!

The TI command only adjusts a setting in the reading head. There is no HF 

communication with the read/write tags.

Summary of Contents for IC-KP-B7-V95



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands