background image

LS682-DA

Safety

 2

0

1

5

-0

5

9

LS68*-DA-F1:

Only use recommended original accessories.

The operating company bears responsibility for observing locally applicable 
safety regulations.

Installation and commissioning of all devices must be performed by a trained 
professional only.

User modification and or repair are dangerous and will void the warranty and 
exclude the manufacturer from any liability. If serious faults occur, stop using the 
device. Secure the device against inadvertent operation. In the event of repairs, 
return the device to your local Fuchs representative or sales office. 

Warning!

Infrared class 1M laser light

Do not observe with optical instruments such as magnifying glasses, 
microscopes, telescopes or binoculars!

Install the device so that the warning is clearly visible and readable.

Maintenance and repairs should only be carried out by authorized service 
personnel!

INVISIBLE LASER RADIATION

DO NOT VIEW DIRECTLY

WITH OPTICAL

INSTRUMENTS

LASER 1M LASER PRODUCT

IEC 60825-1: 2007 CERTIFIED.

COMPLIES WITH 21 CFR 1040.10

AND 1040.11 EXCEPT FOR DEVIA-

TIONS PURSUANT TO LASER NOTICE

NO. 50, DATED JUNE 24, 2007

RAYONNEMENT LASER IN VISIBLE
NE PAS REGARDER DIRECTEMENT
AVEC DES INSTRUMENTS OPTIQUES
PRODUIT LASER CLASSE 1M

CERTIFIÉ CEI 60825-1 : 2007.
CONFORME AUX NORMES 21 CFR
1040.10 ET 1040.11 À L’EXCEPTION
DES ÉCARTS CONFORMÉMENT
À LA NOTICE DU LASER
N° 50, DATÉE DU 24 JUIN 2007.

INVISIBLE LASER RADIATION

DO NOT VIEW DIRECTLY

WITH OPTICAL

INSTRUMENTS

LASER 1M LASER PRODUCT

IEC 60825-1: 2007 CERTIFIED.

COMPLIES WITH 21 CFR 1040.10

AND 1040.11 EXCEPT FOR DEVIA-

TIONS PURSUANT TO LASER NOTICE

NO. 50, DATED JUNE 24, 2007

RAYONNEMENT LASER IN VISIBLE
NE PAS REGARDER DIRECTEMENT
AVEC DES INSTRUMENTS OPTIQUES
PRODUIT LASER CLASSE 1M

CERTIFIÉ CEI 60825-1 : 2007.
CONFORME AUX NORMES 21 CFR
1040.10 ET 1040.11 À L’EXCEPTION
DES ÉCARTS CONFORMÉMENT
À LA NOTICE DU LASER
N° 50, DATÉE DU 24 JUIN 2007.

Caution!

Controls or adjustments

Use of controls or adjustments or performance of procedures other than those 
specified herein may result in hazardous radiation exposure

Summary of Contents for 260312





































Reviews: