Pentair Siata V132 SFE Installer Manual Download

Page: 8 / 88

Installer manual Siata V132 - SFE - Safety

8 / 88

Ref. MKT-IM-003 / B - 19.04.2017

Safety

2.1. Safety

pictograms

definition

2.2.

Safety tags location

Note



Ensure that the safety tags on the device are completely legible and clean. If necessary,
replace them with new tags and put them in the same places.

Caution



Warns of a risk of minor injury or major
material damage to the device or
environment.

Warning



Warns against serious personal injury
and damage to health.

Danger



Warns against serious personal injury or
death.

Mandatory



Standard or measure to apply.

Note



Comment

Prohibition



Restriction to be observed.

Part number

Valve serial number

Serial label

Controller serial number

Serial number

Summary of Contents for Siata V132 SFE

























































































Search results

Summary of Contents for Siata V132 SFE

Reviews:

Related manuals for Siata V132 SFE

Brands by name

Popular brands

Pentair Siata V132 SFE, Installer Manual

Search results

Summary of Contents for Siata V132 SFE

Reviews:

Related manuals for Siata V132 SFE

Brands by name

Popular brands