Pentair PPC5 Series Quick Start Manual Download Page 1

About

 

The PENTEK Pump Controller (PPC5) is pre-jumpered 
and programmed with the PENTEK Assistant, providing 
ease of setup for constant pressure applications. The 
PENTEK Assistant defaults to pre-defined parameters 
as described in this guide, and also prompts the user for 
application-specific information.
This guide covers the startup of the PENTEK Assistant 
for constant pressure applications. For other programs, 
refer to the ABB manual provided. 

SAfety

Hazardous voltage. Can shock, burn, or 

cause death. Ground pump before connecting to power 

supply. Disconnect power before working on system  

components.

Wire pump motor for correct voltage. See motor 

nameplate.

Ground motor to drive before connecting to 

power supply.

Meet National electri cal Code, Canadian elec tri cal 

Code, and local codes for all wiring.

California Proposition 65 Warning

 This product and related accessories contain 

chemicals known to the State of California to cause 
cancer, birth defects or other reproductive harm.

INStAllAtIoN

Connect transducer
Install the transducer where pressure is to be maintained.  
The PENTEK Assistant requires a 4 - 20 ma transducer 
(Figure 2). The transducer’s power lead should be 
attached to terminal 10 or the terminals as shown below 
and the 4 - 20 ma output lead should be attached to ter-
minal 5 (Figure 3). The transducer has a brown power 
lead and a blue 4 - 20 ma output lead.  
(All jumper terminals may need to be loosened to attach 
leads above the jumper board).   
The jumper board eliminates the need to hand wire termi-
nals 9 to 11, 10 to 19, 11 to 12 and 18 to 21.
Before applying power, make sure the front cover is on 
and the control module is in place.

Startup the PENTEK Assistant
Apply power to the unit, and follow the steps on Pages 2 
and 3 after the controller’s screen is lit. 

EXIT

00:00

SAVE

REM

PAR   EDIT

3.0  hp

9909 MOTOR NOM POWER

Scroll

Buttons

Controller Mode

PID Address 
andFunction 
Description 

Value 

Right Button

Right Button
Function

Left Button

Left Button 

Function

Motor Rotation

Indicator

Help

Local / 

Remote

Start

Stop

Local / Remote 

Indicator

fIGuRe 1: Control Panel button location

4 - 20 ma Output

Jumper Board

Power Lead

DIP Switches

+24 volt
Power 
Connection

fIGuRe 3: transducer connection to terminal strip

fIGuRe 2: transducer and Cable

Transducer cable

Transducer

QUICK START GUIDE

PPC5 Series

Pump Controller

© 2012 Pentair, Inc. All Rights Reserved. 

PN770 (11/08/12)

293 WRIGHT STREET, DELAVAN, WI 53115  WWW.PUMPS.COM
PH: 1-866-9 PENTEK

Summary of Contents for PPC5 Series









Reviews: