Operation Instructions
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON are registered trademarks of PENTAIR Corporation
TECHNICAL SUPPORT: IPPBPLUSCU_A 1 of 4
2016 PENTAIR
www.pentair.com
ERICO CADWELD PLUS
Control Unit
GENERAL SAFETY RULES
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
Work area.
Keep your work area clean and well lit.
Do not operate in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust.
Personal safety.
Stay alert, watch what you are doing and
use common sense when operating this tool.
WARNING
1. PENTAIR products shall be installed and used only as indicated in PENTAIR product instruction sheets and training materials.
Instruction sheets are available at www.pentair.com and from your PENTAIR customer service representative.
2. PENTAIR products must never be used for a purpose other than the purpose for which they were designed or in a manner that
exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow PENTAIR
’s instructions and warnings may cause
product malfunction, property damage, serious bodily injury and death.
GENERAL AND SAFETY INSTRUCTIONS:
A.
Only PENTAIR manufactured equipment and materials should be used to make ERICO CADWELD PLUS connections.
B.
Do not connect items except as detailed in instruction sheets. Failure to comply with these instructions may result in improper
and unsafe connections, damage to items being connected, bodily injury and property damage.
C.
Do not use worn or broken equipment which could cause leakage.
D.
Do not alter equipment or material without PENTAIR authorization.
E.
When using ERICO CADWELD PLUS do not use welding material package if damaged or not fully intact. When using ERICO
CADWELD PLUS, do not tamper with or disassemble the welding material unit.
F.
Make connections in conformance with ERICO CADWELD PLUS instructions and all governing codes.
1.
Personnel should be properly trained in the use of this product and must wear safety glasses and gloves.
2.
Avoid contact with hot materials.
3.
Advise nearby personnel of welding operations in the area.
4.
Remove or protect fire hazards in the immediate area.
5.
Provide adequate ventilation to the work area.
6.
Do not smoke when handling starting material
7.
Avoid direct eye contact with “flash” of light from ignition of starting material.
G. Welding material is an exothermic mixture and reacts to produce hot molten material with temperatures in excess of 1400
o
C
(2500
o
F) and a localized release of smoke. These materials are not explosive. Ignition temperatures are in excess of 900
o
C
(1650
o
F) for welding material.
H.
Adhering to the ERICO CADWELD PLUS welding procedures will minimize risk of burns and fire caused by hot molten
material spillage. In case of fire, use of water or CO
2
will aid in control of burning containers. Large quantities of water will aid
in controlling a fire should the exothermic materials become involved. Water should be applied from a distance.
1.
Make sure there is proper mold fit and assembly of equipment.
2.
Avoid moisture and contaminants in mold and materials being welded. Contact between hot molten metal and
moisture or contaminants may result in spewing of hot material.
3.
Base material thickness must be sufficient for the size and type of connection being made to prevent melt-through
and leakage of hot molten metal.
I.
Applications or conditions may exist which require special considerations. The following are examples, but are not intended to
be a complete listing of applications/conditions.
Do not overreach
. Keep proper footing and balance at all
times. Proper footing and balance enable better control in
unexpected situations.
Use safety equipment.
Always wear protective
eyewear and gloves during operation.
Model Number: PBPLUSCU
