Pentair Pool Products PRO-SOURCE, Owner'S Manual

Page: 3 / 35

Splice this ground wire to a copper conductor
that matches motor wire size specified in
Table III. See Page 5 for wire splicing
instructions.
Permanently ground pump, motor and control
box before connecting power cable to power
supply. Connect ground wire to approved
ground first and then connect to equipment
being installed.
Do not ground to a gas supply line.
Fire and electrical shock hazard. If
using a drop wire larger than No. 10 (5.5mm 2 )
(for example, No. 8 (8.4mm
2
) wire) between
pump and control box, run wire to a separate
junction box. Connect junction box to control
box with a No. 10 (5.5mm
2 ) or smaller wire
(depending on amp rating of pump – see
Table III).
For more information, contact your local code
officials.
WIRING CONNECTIONS:
All wiring must meet National Electrical Code or
Canadian Electrical Code and local code
requirements.
Use only copper wire when making connections
to pump and control box.
To avoid over-heating wire and excessive voltage
drop at motor, be sure that wire size is at least as
large as size listed in Table III for your horse-
power pump and length of wire run.
NOTICE: When built-in overheating protection
is not provided, use with an approved overload
equipped motor control that matches motor
input in full load amps. Select or adjust overload
element(s) in accordance with control instruc-
tions. When built-in overheating protection
is
provided, use with an approved motor control
that matches motor input in full load amperes.
TABLE I:
Recommended Fusing Data - 60 Hz.,
Single Phase, 3 Wire Submersible Pump Motors
TABLE II:
Recommended Fusing Data - 60 Hz.,
Single Phase 2 Wire Submersible Pump Motors
INSTALLATION WIRING DIAGRAMS -
SINGLE PHASE, 3 WIRE
For motors of 1 1 ⁄
2
HP and above,
use magnetic starter to avoid damage to pressure
switch. Consult factory for wiring information.
See Page 4 for 2 Wire Hookup.
Hazardous voltage. Can shock,
burn, or kill.
Ground control box, all metal plumbing, and
motor frame with copper wire in compliance
with local codes. Use a ground wire at least as
large as the wires supplying power to motor.
Permanently close all unused openings in this
and other equipment.
Disconnect power to control box before working
on or around control box, pipes, cable, pump,
or motor.
3
Fuse Size
HP Volts Stand Dual Elem.
1/2 115 30 15
1/2 230 15 7
3/4 230 20 9
1 230 25 12
1.5 230 30 15
2 230 30 15
3 230 45 30
Fuse Size
HP Volts Stand Dual Elem.
1/2 115 30 15
1/2 230 15 7
3/4 230 20 9
1 230 25 12
14 12 10 8 6 4 3 2 1 0
Volts HP (2mm 2 ) (3mm 2 ) (5mm 2 ) (7mm 2 ) (13mm 2 ) (21mm 2 ) (25mm 2 ) (34mm 2 ) (41mm 2 ) (50mm 2 )
115 1/2
100 160 250 390 620 960 1190 1460 1780 2160
(30.5) (48.8) (76.2) (118.9) (189) (292.6) (382.7) (445) (542.5) (638.4)
1/2
400 650 1020 1610 2510 3880 4810 5880 7170 8720
(121.9) (198.1) (310.9) (490.7) (765) (1182.6) (1466.1) (1792.2) (2185.4) (2657.9)
3/4
300 480 760 1200 1870 2890 3580 4370 5330 6470
(91.4) (146.3) (231.6) (365.8) (570) (880.9) (1091.2) (1332) (1624.6) (1972.1)
1
250 400 630 990 1540 2380 2960 3610 4410 5360
230
(76.2) (121.9) (192) (301.8) (469.4) (725.4) (902.2) (1100.3) (1344.2) (1633.7)
1-1/2
190 310 480 770 1200 1870 2320 2850 3500 4280
(57.9) (94.5) (146.3) (234.7) (365.8) (570) (707.1) (868.7) (1066.8) (1304.5)
2
150 250 380 620 970 1530 1910 2360 2930 3620
(45.7) (76.2) (118.9) (189) (295.6) (466.3) (582.2) (719.3) (893.1) (1103.4)
3
120 190 300 470 750 1190 1490 1850 2320 2890
(36.6) (57.9) (91.4) (143.3) (228.6) (362.7) (454.2) (563.9) (707.1) (880.9)
TABLE III:
Power Supply Wire (Cable) Length in Feet (M)
1 Phase, 2 or 3 Wire Cable, 60 Hz (Copper Wire Size - Service to Motor)