Pentair Pool Products PENTEK G2D-01 Owner And Operational Manual Download Page 8

Page: 8 / 10

1 Phase Simplex
Control Panel for Grinder
and Vortex Pumps

Owner and Operational Manual

293 S. Wright St, Delavan, WI 53115 Phone: 1-866-973-6835 Fax: 800-426-9446

1 Phase Simplex - How to use the System Test switch

If the indicator lights are illuminated the fuses are good.

#1. Check the incoming power on the top of the command center.

If one or both of the indicators
are not illuminated the fuse or
fuses need to be replaced. If
the fuse or fuses do not fix the
problem the incoming power
needs to be examined.

Alarm Fuse needs
to be replaced

Control Fuse
needs to be

#2. View the current status of your system.

The indicator lights illuminate as each float rises with the liquid
level in the tank.

#1.

Alarm Float

Start Float

Stop Float

Alarm Float

Start Float

Stop Float

All three floats are not activated. Only the Control
Power and Alarm Power indicator lights should be
illuminated.

If the Stop float is activated the Stop light
will illuminate.

The Stop float and the Start float are
activated so the Stop float and the Start
float indicator lights are illuminated.

All floats are up so all indicators are illuminated.

Stop Float

Start Float

Alarm Float

Stop Float

Start Float

Alarm Float

Fuses are good.

#2.

#3.

#4.

P10063VSM

Page 8 of 10

Summary of Contents for PENTEK G2D-01











Search results

Summary of Contents for PENTEK G2D-01

Reviews:

Related manuals for PENTEK G2D-01

Brands by name

Popular brands

Pentair Pool Products PENTEK G2D-01, Owner And Operational Manual

Search results

Summary of Contents for PENTEK G2D-01

Reviews:

Related manuals for PENTEK G2D-01

Brands by name

Popular brands