manualshive.com logo in svg

PenBits BACHMANN CLASS 24, Assembly Instructions Manual, Page: 35 / 52

Share
Download
PenBits BACHMANN CLASS 24 Assembly Instructions Manual Download Page 35

Modifying the Bogie Drive

This  section  describes  the  operations  involved  in  modifying  the  drive  unit  for  one
bogie.

Using  a  small  screwdriver,  gently  unclip  the
bogie 

sideframe/undertray moulding  from

the ends of the bogie drive unit. Take care not
to  damage  the  brake  shoe  and  step  detail. Put
the moulding safely to one side for now.

Unclip the two wheelsets from the drive train moulding and put them to one side.

Undo 

the 

two 

cross-headed 

screws

retaining the bogie pivot to the tops of the

two pivot towers …

…  and  remove  the  pivot.  These  parts  are
not required for the converted bogie.

Undo the cross-headed screws which retain
the  metal  pickup  strips  on  the  side  of  the

drive train  moulding.  Remove  the  strips  and,
with  a  sharp  knife,  the  moulded  pips  which
locate them.  Put the pickup wires and strips to
one side for reuse.

Modifying the bogie drive

35/51

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Summary of Contents for BACHMANN CLASS 24





















































Reviews:

No comments