background image

 

© Presby Environmental, Inc., Maine Design & Installation Manual, June 2019 Edition                                       -12-

 

16.0  Basic Serial Distribution (Multi-Level™) 

Basic Serial Multi-Level™ systems can use AES  or ES pipe and must conform to the requirements for single level 

basic serial systems except: 

a)  Pipe requirements per 

Table E

 (see para. 7.0, pg. 5). 

b)  Row spacing per 

Table F

 (see para. 8.0, pg. 5). 

c)  All Multi-Level™ beds require venting. Upper and Lower Level Rows may be vented separately. If only a 

single vent is used, it must be connected to the last row in the series on the Lower Level. 

d)  Multi-Level™ systems are limited to Soil Profiles 2, 4, 5 & 6. 

e)  For beds sloping over 10% the System Sand Extension must be 12 in. thick 

f)  The fill extension is measured from the AES or ES pipe (measured from the Upper Rows) before starting 

the 4:1 side slope tapers. 

g)  A minimum of 6 in. of System Sand separates the Upper Level Rows from the Lower Level Rows  

h)  Effluent is delivered first to the Upper Rows, which then connects to the Lower Level Rows by way of a 

Drop Connection. 

i)  The Drop Connection must pitch downward toward the Lower Level at least 2 inches. 

 

Illustrations of Multi-Level™ Basic Serial Systems: 

 

Illustration of sloping Multi-Level™ Basic Serial System: 

 

17.0  Bottom Drain 

A bottom drain is a line connected to the hole in the 6 o’clock position of a double offset adapter at the end of each 

serial section or each row in a D-box Distribution Configuration which drains to a sump and is utilized to lower the 

water level in a saturated system or to facilitate system rejuvenation.  

1

0

'

M

IN

BOTTOM 

DRAIN SUMP

SOM

E ROW

N

O

T

 S

H

O

WN

VENT

4"Ø BOTTOM 

DRAIN MANIFOLD

SOM

E ROW

N

O

T

 S

H

O

WN

SOM

E ROW

N

O

T

 S

H

O

WN

VENT

18"

LOCK OR BOLT 

COVER CLOSED

BOTTOM DRAIN CONNECTED TO SIX O'CLOCK POSITION OF DOUBLE OFFSET ADAPTERS AT THE END 

OF EACH ROW OR SERIAL SECTION. THE VENT MANIFOLD IS ATTACHED TO THE TWELVE O'CLOCK 

POSITION OF THE DOUBLE OFFSET ADAPTER (OVER EACH BOTTOM DRAIN CONNECTION).

3'

VENT MANIFOLD - CONNECT ENDS OF ALL 
ROWS OR ENDS OF ALL SERIAL SECTIONS

TYPICAL BOTTOM DRAIN APPLICATION

PAVEMENT

Summary of Contents for Advanced Enviro-Septic
































Reviews: