Peco WavePRO R2500 Installation Manual Download Page 1

Benefi ts:

•  Reduced installation time
•  Reduced wiring costs
•  Energy cost savings

•  Scalability of network
• Flexibility in fl oor planning
•  Ideal for building renovation

PECO WavePRO

 Wireless System 

INSTALLATION GUIDE: 
T2500 THERMOSTAT AND R2500 RECEIVER

Wireless control for up to 3-HEAT/ 2-COOL 
heat pump and conventional systems 
(gas,oil,electric).  

The Peco WavePRO Wireless System

The PECO WavePRO

 Wireless System is a wireless thermostat transmitter and 

receiver. It is designed for use with conventional (gas, oil, electric) or heat-pump 
systems. It can support up 2-HEAT/ 2-COOL confi guration on conventional systems 
and up to 3-HEAT/ 2-COOL confi gurations of heat pump systems. The PECO 
WavePRO Wireless System is comprised of the wireless T2500 Thermostat paired with 
the wireless R2500 Receiver. 
The T2500 Thermostat may be powered by battery, 24 VAC, or by both 
(recommended). The system may be programmed for 7-day individual, 5/2-day, 
5/1/1-day, or 7-day identical programmable operation, with four time periods per day. 
The R2500 Receiver is powered by 24 VAC only and is wired directly to the HVAC 
equipment it controls. 

Summary of Contents for WavePRO R2500





















Reviews: