manualshive.com logo in svg

Peak PCAN-DONGLE IPEH-002019, User Manual, Page: 18 / 34

Share
Download
Peak PCAN-DONGLE IPEH-002019 User Manual Download Page 18

PCAN-Dongle – User Manual 
 

18 

4.3

 

Operating Modes 

The PCAN-Dongle can be used in one of four possible operating 
modes: 

Name of operating 
mode 

Alternative 
identifier 

Description 

Multiplex Mode 

PEAK Dongle-CAN  Standard Parallel Port (SPP) 

EPP Mode 

PEAK Dongle-CAN 
EPP 

Extended Capability Port (ECP) 

Multiplex PeliCAN 
Mode 

PEAK Dongle-CAN 
SJA 

Standard Parallel Port (SPP), 
extended CAN functionality (CAN 
2.0B incl. 29-bit IDs) 

EPP PeliCAN Mode 

PEAK Dongle-CAN 
SJA EPP 

Extended Capability Port (ECP), 
extended CAN functionality (CAN 
2.0B incl. 29-bit IDs) 

 

The EPP PeliCAN Mode is recommended to gain the full CAN 
functionality at lowest possible computer system load. If this mode 
doesn't work correctly, you can fall back to one of the other 
operating modes. The Multiplex Mode should work on any system. 

Tip:

 You can find further information about the PeliCAN Mode 

in the data sheet for the CAN controller SJA1000 by NXP 
obtainable at the according website, for example. 

You can find information about activating an operating mode in the 
following section. 

Summary of Contents for PCAN-DONGLE IPEH-002019



































Reviews:

No comments