background image

PEAK® OEM 32 24 Volt SMART Equipment Controller Installation Instructions

22

Refer to the 

MS/TP Communications Bus Technical  Bulletin (LIT-12011034) 

for detailed information  about wire 

size and cable length requirements for  the SA and FC buses.

Refer to the 

N2 Communications Bus Technical  Bulletin (LIT-636032) 

for detailed information about wire size 

and cable length requirements for  the N2 bus. 

Table 7:  Communication bus and supply power terminal blocks, functions, ratings, requirements, and 

cables

Terminal 

block/port 

label

Terminal labels

Function, electrical ratings/

requirements

Recommended cable type

FC BUS/

SA BUS

FC BUS 

(Upper)

+

FC bus communications

0.6 mm

2

 (22 AWG) stranded, 3-wire  twisted, 

shielded cable is best practice

-
COM

Signal reference (Common) for bus 

communications

SHD

Isolated terminal (optional shield 

drain connection)

SA BUS

(Port)

SA BUS

RJ-12 6-Position Modular Connector 

provides: SA bus communications
SA bus signal reference and 15 VDC 

common
15 VDC, 71.5 ohms at 4 W, power for 

Bluetooth Commissioning Converter 

or ZFR3211 Wireless Router

N/A (24 AWG) 3-pair CAT3 cable <30.5 m (100 

ft)

FC BUS/

SA Bus

SA BUS 

(Lower)

+

SA bus communications

0.6 mm

2

 (22 AWG) stranded, 4-wire  (2 twisted-

pairs), shielded cable is best practice.

Note:

The + and 

-

 wire are one twisted pair, 

and the COM and SA PWR are the second 

twisted pair of wires.

-
COM

SA bus signal reference and 15 VDC 

common

PWR

15 VDC supply power for devices on 

the SA bus (Maximum total current 

draw for SA bus is 240 mA.)

24~ INPUT

HOT

24 VAC Power Supply 

– 

Hot

Supplies 20 VAC–30 VAC (Nominal 

24 VAC)

0.8 mm

2

 to 1.5 mm

2

 

(32 AWG) 2-wire

COM

24 VAC Power Supply Common 

(Isolated from all other  common 

terminals on controller)
20 VA at 24 VAC nominal

MODBUS

+

Modbus communications

0.6 mm

2

 (22 AWG) stranded, 4-wire 

(2 twisted pairs), shielded cable is best 

practice

-
COM

Signal reference (Common) for bus 

communications

24~ OUT

24~

24 VAC Utility Supply 

(for actuators) 

- 80 mA continuous

0.8 mm

2

 to 1.5 mm

(18 AWG) 2-wire

COM

24 VAC Power Supply Common

Summary of Contents for OEM 32




























Reviews: