background image

Issue 1.34 

IBDH/IBUH/TLTH/ILAH Installation and Operation Handbook 

Page 6 

 

REAR PANEL PINOUTS   

 

 

 

 

 

 

 

Remote 

15 Way D type Female on the chassis with connections as follows 

 

 

 
 
 
 
 
 
 
 

 

Alarms 

15 Way D type Male on the chassis with connections as follows 

There are 2 independent relays controlled together designated (1) and (2) as follows. Important 
note : N/O means 'normally open' in the non fail state with STATUS LED Green 

 

 

 
 
 
 
 
 
 
 

 

If the mute option is fitted then the unit will be muted unless the above Ext. Mute pin is joined to 
GROUND. 
 

Redundancy 

9 Way D type Male on the chassis with connections as follows 

 

 
 

 

 

 

RS485 Rx + 

RS485 Tx + 

Not used 

Not used 

Not used 

Not used 

RS232 Rx In 

Not used 

RS485 Rx - 

10 

RS485 Tx - 

11 

Not used 

12 

Not used 

13 

Not used 

14 

GROUND 

15 

RS232 Tx Out 

Unit fault (1) COM 

Unit fault (1) N/C 

Ext Mute (1) 

Unit fault (2) COM 

Unit fault (2) N/C 

Not used 

Not used 

Not used 

Unit fault (1) N/O 

10 

Not used 

11 

Not used 

12 

Unit fault (2) N/O 

13 

Not used 

14 

Not used 

15 

GROUND 

Not used 

CAN

 Low 

GND 

Power A 

Power B 

GND 

CAN

 High 

Tellback A 

Tellback B 

Summary of Contents for IBDH Series



















Reviews: