background image

    To replace the battery of the motor, you need to press the battery to the right first, and 

then pull it out. (Refer to the direction of the laser indicator on the lower right of the motor.) 

If the battery is difficult to access due to excessive sweating, you can use a power sticker 

to help remove the battery.

M

O

T

O

R

 

M

IN

I

Press the battery 

to the right first

Then unplug the battery

Notice

- Stop calibration: the motor jumps teeth during the automatic calibration process, 

which causes the phenomenon of non-stop rotation. You only need to click once 

of the motor button to terminate the calibration;

- When the rotation stroke of the motor does not match the calibrated stroke, 

please check whether the indicator light of the Bluetooth controller is flashing blue 

and the current battery color alternately. If the above state appears, it means that 

the controller has set the stroke of point AB Limit, you need to short press the 

controller button to start AB automatic operation, and then short press again to 

cancel the automatic operation and cancel the AB point stroke limit.

- The controller defaults FOCUS mode. If it is switched to  ZOOM mode, it will be 

equally divided based on the rotation of the wheel 300 degrees, and the middle 

10 degrees is the static position. Turn to the left to advance forward, and turn to 

the right to advance backward. The advancing speed is adjusted linearly 

according to the angle of rotation.

- The motor defaults to the lens control mode. For example, after switching to the 

electric slide/pan/tilt mode, when the motor starts without Bluetooth connection, it 

will automatically calibrate the stroke and run automatically in a constant speed 

cycle.

- Regarding battery maintenance: When the product is not used for a long time, it 

is recommended to check the power of the device every other month to ensure 

that the battery has sufficient power; when the device is in a low or no power state 

for a long time, the battery capacity will decrease.

Slow

Fast

Slow

Fast

Stop

*ZOOM mode needs to be used 
 with ZOOM RIG accessories.

Summary of Contents for Live Air 2S












Reviews: