PDL D3-2.5, Instruction Manual, Page: 43 / 113

Microdrive Series Instruction Manual
4201-109 Rev I
43
Table 2.1.1 Display Screen Messages - Full Menus
THE DISPLAY:
STATUS LINE
ð
STP 0.0A +0.0Hz
ï
ALWAYS DISPLAYED
CONTROL LINE
ð
T=0.0% R= +0.0Hz
ï
CAN BE SCROLLED TO SEE MANY OTHER SCREENS
STATUS LINE :
SCREEN DESCRIPTION NOTES
STP 0.0A +0.0Hz STATUS ALWAYS DISPLAYED
CONTROL LINE :
Note: Default (factory set) values are shown in the control line where appropriate.
LOCAL CONTROLS:
NO. SCREEN DESCRIPTION MIN/MAX UNITS
-3* 00000000 00 00 CONTROL INPUT DISPLAY ; % ;%
-2* KB FREQ= +0.0Hz KEYBOARD FREQUENCY CONTROL -200/+200 HERTZ
-1* STOP-RST START KEYBOARD STOP/RESET-START - -
EXTENDED STATUS SCREENS:
NO. SCREEN DESCRIPTION UNITS
0* T=0.0% R= +0.0Hz MOTOR TEMPERATURE; REFERENCE FREQ. %, HERTZ
1* Vdc=565V Vo=400V DC BUS VOLTAGE; OUTPUT VOLTAGE V(DC);V(AC)
2* NO FAULTS FAULT DISPLAY
ADJUSTMENT SCREENS: * Present in Short Menus
NO. SCREEN DESCRIPTION MIN/MAX UNITS
10* 10 MTR CUR= I(Inv.) RATED (NAMEPLATE) MOTOR CURRENT 0.20/1.50xI(Inv.) AMPS
11* 11 MTR VOLT=415V RATED (NAMEPLATE) MOTOR VOLTAGE 10/995 AC VOLTS
12* 12 MTR FR = 50Hz RATED (NAMEPLATE) MOTOR FREQUENCY 10/250 HERTZ
13 13 MTR COOL= 40% MOTOR COOLING AT ZERO SPEED 5/100 %
14* 14 BOOST = 0.0% TORQUE BOOST VOLTAGE AT ZERO SPEED 0.0/15.0 %V(MOTOR)
15* 15 ACC1=10.0Hz/s ACCELERATION RATE (NORMAL) 0.02/500 HERTZ/SEC
16* 16 DEC1=10.0Hz/s DECELERATION RATE (NORMAL) 0.02/500 HERTZ/SEC
17 17 T CONST= 0.05s FEEDBACK/S-CURVE TIME CONSTANT 0.0/0.5 SECONDS
18 18 I LIMIT= 1.2 I(Inv.) CURRENT LIMIT 0.05/1.50xI(Inv.) AMPS
19 19 ILT T/O=NONE CURRENT LIMIT TIME OUT 0.0/25.0/NONE SECONDS
20 20 ILT SLIP=4.0% CURRENT LIMIT SLIP VALUE 0.0/9.9/OFF %
21 21 MIN FR= 0.0Hz MINIMUM FREQUENCY 0.0/MAX FREQUENCY HERTZ
22 22 MAX FR= 60.0Hz MAXIMUM FREQUENCY MIN FREQ/200 HERTZ
23* 23 FR F1= +0.0Hz REFERENCE FREQUENCY SETPOINT 1 -200/+200 HERTZ
24* 24 FR F2=+60.0Hz REFERENCE FREQUENCY SETPOINT 2 -200/+200 HERTZ
25 25 MIN FLUX=100% DYNAFLUX MINIMUM FLUX LEVEL 40/100 %V(MOTOR)
26 26 DC LEVEL =0.0% DC(0Hz) HOLD/BRAKE VOLTAGE AT STOP 0.0/25.0 %V(MOTOR)
27 27 DC TIME =0.0s PERIOD OF DC HOLD VOLTAGE AT STOP 0.0/25.0 SECONDS
28 28 DC HEAT =OFF DC HEATING VOLTAGE DURING STOP OFF/0.1/10 %V(MOTOR)
29 29 FR ON =12.0Hz FREQUENCY RELAY UPPER SET POINT RELAY OFF/200 HERTZ
30 30 FR OFF=10.0Hz FREQUENCY RELAY LOWER SET POINT 0.0/RELAY ON HERTZ
31 31 I-SENSE= I(Inv.) CURRENT RELAY SET POINT (5% HYST.) 0.00/1.50xI(Inv.) AMPS
32 32 M-FR1= +0.0Hz MULTISPEED FREQUENCY 1 (INCH 1) -200/+200 HERTZ
33 33 M-FR2= +0.0Hz MULTISPEED FREQUENCY 2 (INCH 2) -200/+200 HERTZ
34 34 M-FR3= +0.0Hz MULTISPEED FREQUENCY 3 -200/+200 HERTZ
35 35 M-FR4= +0.0Hz MULTISPEED FREQUENCY 4 -200/+200 HERTZ
36 36 M-FR5= +0.0Hz MULTISPEED FREQUENCY 5 -200/+200 HERTZ
37 37 M-FR6= +0.0Hz MULTISPEED FREQUENCY 6 -200/+200 HERTZ
38 38 M-FR7= +0.0Hz MULTISPEED FREQUENCY 7 -200/+200 HERTZ
39 39 ACC2=10.0Hz/s ALTERNATIVE ACCELERATION RATE 0.02/500 HERTZ/SEC
40 40 DEC2=10.0Hz/s ALTERNATIVE DECELERATION RATE 0.02/500 HERTZ/SEC
41 41 BRK FR= 0.0Hz BREAK FREQUENCY FOR ACCEL/DECEL 0.0/200 HERTZ
42* 42 DEC3=10.0Hz/s EMERGENCY STOP DECELERATION RATE 0.02/500 HERTZ/SEC
43 43 T GAIN =20.0 PULSE TACHO INPUT SCALING FACTOR 1.0/999 OP Hz / IP KHz
44 44 DB TIME = 10s TIME CONSTANT OF BRAKE RESISTOR 0/250 SEC
45 45 DB DUTY = OFF % DUTY RATING OF BRAKE RESISTOR 5/100/OFF %
46 46 SLIP FR=0.0% FULL LOAD SLIP COMPENSATION 0.0/9.9 %
47 47 SK FR1= 0.0Hz SKIP FREQUENCY 1 0.0/200 HERTZ
48 48 SK FR2= 0.0Hz SKIP FREQUENCY 2 0.0/200 HERTZ
49 49 SK BW= 0.0Hz SKIP BAND WIDTH 0.0/10.0 HERTZ
50 50 COMMS ADR= 10 SERIAL COMMUNICATIONS ADDRESS 1/240 -
51 51 BAUDRATE= OFF SERIAL COMMUNICATIONS BAUD RATE 1200/4800/9600/OFF BAUD
52 52 VLT SLIP= 4.0% VOLTAGE LIMIT SLIP 0.0/9.9 %
53 53 DAMPING= 0.8% NO LOAD DAMPING 0.0/5.0 %
54 54 FB RLY = 10.0 Hz HYSTERESIS ON FEEDBACK RELAY 0.0/200 HERTZ