3. Reader Connection
2. Mounting Controller
6. Locking Relay
5. Input B / REX Connection
4. Input A / DPS Connection
1. Package Contents
Jumpers (16)
Diodes (8)
Red 8
Eight Door Controller (1)
Battery Leads (1)
Can Lock (1)
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BUS
+
-
BUS
+
-
POE IN
POE OUT
12-24
BATTERY
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
OSDP
OSDP
OSDP
OSDP
PORT2
PORT3
PORT4
PORT1
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BUS
+
-
BUS
+
-
POE IN
POE OUT
12-24
BATTERY
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
OSDP
OSDP
OSDP
OSDP
PORT2
PORT3
PORT4
PORT1
AC1
AC
DC
NC
C
NO
NC
C
NO
eFlow102B
5A 250V
15A 32V
eFlow102NB
L
G
N
ALTRONIX CORP.
BROOKLYN,
N.Y. 11220
+ AU
X –
TRIGG
ER E
OL
SUPERVISED
RESETNO
GND
+
- DC
+
- BAT
Mount
-
Mount the Red 8 enclosure securely to a wall.
A
Reader(s)
-
Use a 22/5 or 22/6 wire to wire the reader to the controller, as
shown above. Be sure to check polarity and voltage prior to powering the
controller.
B
OSDP
-
Place jumper to enable OSDP (see OSDP reference guide at the end
of this guide for more info)
OSDP
Wiring
+ -
0 1 L
B
A
Reader(s)
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BUS
+
-
BUS
+
-
POE IN
POE OUT
12-24
GND
+
BATTERY
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
OSDP
OSDP
OSDP
OSDP
PORT2
PORT3
PORT4
PORT1
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
A
A
A
OSDP
+
A
DPS (Door Position Switch)
- The DPS is mounted on the door frame in the
desired location with a 22/2 wire running from the DPS to the controller.
Wire the DPS to the controller as shown above. When using two DPS sensors
for double doors, you will wire them in series with only two conductors
running back to the controller for connection.
AUX Input
- A rule can be set up to trigger events or outputs based on this
input trigger.
B
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BUS
+
-
BUS
+
-
POE IN
POE OUT
12-24
GND
+
BATTERY
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
OSDP
OSDP
OSDP
OSDP
PORT2
PORT3
PORT4
PORT1
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
A
DPS Contact
B
A
-
B
Double
DPS Contact
Maglock
-
When installing a Maglock, it is typical to install a REX (Request to
Exit) at the door for free egress. Run an 18/2 wire from the Maglock to the
Door Controller, connecting to the Maglock as shown.
REX (Request to Exit)
-
The REX is mounted in the desired location with an
18/5 wire ran from the REX to the controller. Wire the REX to the controller
and Maglock, as shown above. If reporting is not needed in the system, simply
eliminate the green-labeled wire.
A
B
Jumper Block(s)
-
Use to designate (+) or (-) board voltage out of NO and NC.
If the jumper is off, the relay is a standard dry contact needing input into
common.
C
AUX Input
-
A rule can be set up to trigger events or outputs based on this input trigger.
If using a powered REX,
run to any 12VDC output
on controller.
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BUS
+
-
BUS
+
-
POE IN
POE OUT
12-24
GND
+
BATTERY
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
OSDP
OSDP
OSDP
OSDP
PORT2
PORT3
PORT4
PORT1
+
-
0
1
L
A
-
B
NC
NO
C
+
-
0
1
L
A
-
B
NC
NO
C
Maglock
B
REX
A
C
BUS
+
-
POWER
HEART
LINK
BUS
+
-
BUS
+
-
BA
TTER
Y
+ -
0 1 L
A
-
B
NC NO
C
+ -
0 1 L
A
-
B
NC NO
C
OSDP
OSDP
PORT2
PORT1
D
BUS
+
-
C
A
B
OR
Diode
- The provided diode must be installed when using a strike. Install at
the strike with the grey stripe of the diode on positive and the black on
negative.
A
NC
- Used for maglocks (or strikes in fail-safe configuration). Connect the
negative (-) of the maglock or strike to NC on the door controller.
B
NO
- Used for strikes in fail-secure configuration. Connect the negative (-) of
the strike to NO on the door controller.
C
Jumper Block
- Use to designate (+) or (-) board voltage out of NO and NC. If
the jumper is off, the relay is a standard dry contact needing input into
common.
D
