PCB Piezotronics Larson Davis EPS044 Reference Manual Download Page 14

Page: 14 / 57

NMS044 Reference Manual Rev E

Obtaining Cellular Service for the RV50X

2-2

FIGURE 2-1

Battery Installation

TAKE NOTE

The 831C power button

controls the power in the whole system. It is used to turn off

and on the NMS044. Additionally, connecting the battery will also turn the system on.

2.2.2 Charging the Battery

We recommended that you charge the battery prior to deployment

using the included PSA039 AC Battery Charger.

Step 1

Connect the solar connectors together, and use the plug to

connect to an external power source (wall outlet) until

charged.

TAKE NOTE

You will know it is fully charged when the PSA038 Genasun Solar Charge Controller LED is

green (Blinking indicates charging, Solid green indicates charge is full). If there is no light,

ensure the battery is properly installed and the system is turned on. For more

information, see A.5.3 "PSA038 Genasun Solar Charge Controller" on page A-5.

2.3 Obtaining Cellular Service for the RV50X

The RV50X gateway requires a data plan, SIM card, public IP address,

and an APN for access and service.

Step 1

Purchase a SIM card with the following features:

• A data plan sufficient to the NMS044 data usage. The NMS044

does not regulate data use. Significant charges may occur if the

plan is exceeded.

• No messaging/voice data is needed.

CAUTION

The yellow

connector does not

connect in the power

block. Do not attempt to

connect the yellow

connector to a red or black

connector.

Summary of Contents for Larson Davis EPS044


























































Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands

PCB Piezotronics Larson Davis EPS044, Reference Manual

Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands