PAW FriwaMega - DN 32 Page 4 Installation And Operation Instructions Manual Download | Manualshive

Page: 4 / 32

background image

1 General Information

4

99640766x-mub-en – V03

2014/11

1

General Information

1.1

Scope of these instructions

These instructions describe the installation, commissioning, function and operation of the
domestic hot water module FriwaMega.
The chapters called [specialist] are intended for specialists only.
For other components of the system, such as tanks, controllers or pumps, please observe
the instructions of the corresponding manufacturer.

Item

Item number

Controller

FC3.8

Pump

primary

Circulation

Heat

exchanger

FriwaMega

6407660

Grundfos

UPM XL 25-125

Optional:

Grundfos

UPM2 15-75 CIL2

or

Grundfos

UPML 25-105 N

2 x 60 plates

FriwaMega

with

circulation

6407661

Grundfos

UPM XL 25-125

Grundfos

UPML 25-105 N

2 x 60 plates

6407662

Grundfos

UPM XL 25-125

Grundfos

UPM2 15-75 CIL2

2 x 60 plates

Carefully read these instructions before installation and commissioning.
Save these instructions in the vicinity of the installation for future reference.

«
...
2
3
4
5
6
...
»

Summary of Contents for FriwaMega - DN 32

































Reviews:

No comments

Related manuals for FriwaMega - DN 32

Brand: Zibro Pages: 16

Brand: Danfoss Pages: 16

aroSTOR VWL B 200/5 UK

Brand: Vaillant Pages: 24

Brand: Vaillant Pages: 20

Brand: Vaillant Pages: 24

Brand: Watson Marlow Pumps Pages: 95

Brand: Watson Marlow Pumps Pages: 87

Brand: Watson Marlow Pumps Pages: 127

Brand: ubbink Pages: 31

Brand: Calienta Pages: 58

Altherma EKHWE150A3V3

Brand: Daikin Pages: 10

Brand: EBARA Pages: 48

Brand: Omega Altise Pages: 8

Brand: Talhu Oy Pages: 11

Brand: UNITED Pages: 5

Brand: Virax Pages: 52

Brand: Zip Pages: 24

Brand: EDM Product Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands