manualshive.com logo in svg

Patton EdgeRoute 6081RC, User Manual, Page: 20 / 49

Share
Download
Patton EdgeRoute 6081RC User Manual Download Page 20

20

Chapter 2

Hardware installation

Chapter contents

Introduction

..........................................................................................................................................................21

Unpacking the Model 6081RC

.............................................................................................................................21

Installing the PMC Ethernet Access Module onto the 6081RC front blade

...........................................................22

Model 6081RC blades installation

.........................................................................................................................23

Cable installation

...................................................................................................................................................25

Connecting the Ethernet ports

 ........................................................................................................................25

Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub

 ...............................................26

Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC

 ................................26

Connecting the EIA-561 RS-232 configuration port (DCE configured)

 .........................................................27

Completing the hardware installation

....................................................................................................................27

Summary of Contents for EdgeRoute 6081RC


















































Reviews:

No comments