ASSEMBLY INSTRUCTIONS (continued)
ASSEMBLY INSTRUCTIONS (continued)
Page 5 of 7
200810
● The shut-off delay is the length of time the light will stay at brightness after motion
is detected.
● You can set the shut-off delay by rotating the “TIME” knob arrow so it points to the desired time setting (from 5
seconds to 3 minutes). To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay,
turn the knob counterclockwise.
Shut-off Delay
Customization Options
Note: To make sure the above functions operate properly, always keep the wall switch in the “ON” position
(including the daytime).
● When slide the mode selector to “OFF”, the light turn
s off automatically. It turns to high-level brightness
when motion is detected, and stays on as long as the motion continues. Then turns off about 5 seconds
after motion is no longer detected.
● When slide the mode selector to “3H” or “6H” or “D2D
”, the light turns to low-level brightness automatically.
It turns to high-level brightness when motion is detected, and stays on as long as the motion continues.
Then reverts back to low-level brightness about 5 seconds after motion is no longer detected.
2. OFF MODE (nighttime operation only)
●
To shift to the “OFF” mode, rotate “Time” knob arrow to the desired time setting (between 5 seconds and 3
minutes). At dusk, the light stays off, it turns on when motion is detected, and stays on as long as motion
continues. When the motion is no longer detected, it remains on for the predetermined time you set (5s ~ 3min),
and then turns off automatically.
● The light turn
s off automatically at dawn.
3. 3 HOUR MODE (nighttime operation only)
● To shift to the “3H” mode,
place the slide switch to “3H” position, and rotate “Time” knob arrow to the desired time
setting (between 5 seconds and 3 minutes). At dusk, the light turns to low- level brightness automatically. From
this moment on, it will remain on for 3 hours. During this 3 hours, when motion is detected, it turns to high-level
brightness, and stays on as long as motion continues. When the motion is no longer detected, it remains high-
level brightness for the predetermined time you set (5s ~ 3min), and then turns to low-level brightness
automatically. After the 3 hours, it turns off. when motion is detected again, it turns to high-level brightness, and
stays on as long as motion continues. When the motion is no longer detected, it turns off after the predetermined
time you set (5s ~ 3min).
● The light turn
s off automatically at dawn.
4. 6 HOUR MODE (nighttime operation only)
● To shift to the “6H” mode,
place the slide switch to “6H” position, and rotate “Time” knob arrow to the desired time
setting (between 5 seconds and 3 minutes). At dusk, the light turns to low- level brightness automatically. From
this moment on, it will remain on for 6 hours. During this 6 hours, when motion is detected, it turns to high-level
brightness, and stays on as long as motion continues. When the motion is no longer detected, it remains high-
level brightness for the predetermined time you set (5s ~ 3min), and then turns to low-level brightness
automatically. After the 6 hours, it turns off. when motion is detected again, it turns to high-level brightness, and
stays on as long as motion continues. When the motion is no longer detected, it turns off after the predetermined
time you set (5s ~ 3min).
● The light turns off automatically at dawn.
5. D2D MODE (nighttime operation only)
● To shift to the “D2D” mode,
slide switch to “D2D” position, and rotate “Time” knob arrow to the desired time setting
(between 5 seconds and 3 minutes). At dusk, the light turns to low-level brightness automatically, it turns to high-
level brightness when motion is detected, and stays on as long as motion continues. When the motion is no
longer detected, it remains on for the predetermined time you set (5s ~ 3min), and then switch back to low level
brightness.
● The light turns off automatically at dawn.
FUNCTION AND OPERATION (continued)