background image

 20

IQAN-G2 Technical Overview

Appendix A

Instruction book, IQAN-G2

Recommended Operating Conditions

a

Parameter

Limit values

Unit

Remark

min.

typ.

max.

Recommended operating temperature, 
T

ROC

– 30

+70 

°C

Voltage supply, V

BAT

9

32

V

a.Recommended operating conditions are given for maximum and minimum conditions where nor-
mal performance is still available from the device. Once the normal operating conditions are exceed-
ed, the performance of the device may suffer. 
Also, the operating temperature for the manufactures´s SIM card may differ from the IQAN-G2 rat-
ings. Consult the service provider to determine the temperature rating for the SIM card.

System

T

A

 = +25 °C (unless otherwise specified)

Parameter

Limit values

Unit

Remark

min.

typ.

max.

Weight

650

grams

Current consumption, while GSM
transmission in progress

400
200

mA

@14 Vdc
@28 Vdc

Approvals

Parameter

Remark

EU Directives
EN 61000-6-2 (03/2006)
EN 61000-6-3

Immunity standard for industrial environments
Emission standard for residential, commercial, 
and light industrial environments

US Standards met
FCC 15/47 CFR Ch 1 (10-01-2010)
FCC 15/47 CFR Ch 1 (10-01-2010)

Conducted emission limits
Radiated emission limits

Summary of Contents for IQAN-G2



























Reviews: