Parker Hannifin Corporation
Cylinder Division
Des Plaines, Illinois
www.parker.com
/cylinder
Hydraulic and Electrohydraulic Actuators
HAS Series Analog Drives Manual
Catalog HY08-4005-M3
30
WARNING:
This product can expose you to chemicals including
Lead and Lead Compounds
which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
PROP 65 WARNING
Input Overview
R
Reettrraacctt LLS
S ((IInnppuutt))
When True (High) drive will ramp HAS unit to a stopped
condition in retract motion only. Ramp time value is set by
keypad entry Page 23 for details. It is recommended to
remove CMD input when this condition is seen.
P
Prrooffiilleerr ((iinnppuutt))
When True (High) drive will spin at a 2nd predetermined
speed setting. This function allows for fast approach and
transitions to slow speed approach. Also useful for extend
and retract speed matching. See page 27 for more details.
R
Reesseerrvvooiirr LLeevveell ((iinnppuutt))
Option Reservoir Low Oil level detection input, unit must be
equipped with reservoir level switch function. Default setting
when tripped (High) will issue a Low Oil Level Warning on Key
pad. Through Keypad entry device can be set to "Trip" drive
in Fault Condition See Page 39 for more details
S
Soouurrcciinngg O
Ouuttppuuttss
C
CW
W LLiim
miitt aanndd C
CC
CW
W LLiim
miitt
HAS Units equipped with Limit Switch or with Stop On
PSI mode set. When condition is seen and motion
stopped, discrete output is set for indication of
condition.
For Stop on PSI see page 36 for details.
Faulted
If the drive trips under Fault condition, this output is
set true.
E
Ennaabbllee ((IInnppuutt))
When True (High) drive will react to other discrete
inputs. When False (Low) inputs are ignored.
C
CW
W C
CM
MD
D ((IInnppuutt))
When True (High) drive will spin the pump in a clockwise
function. HAS Speed is set by the V1setting on key pad
setup, see Page 22 for details.
The HAS orientation call out in the model code set the
extend and retract direction. Orientations "A" &
"H"(reservoir on Cap end) CW rotation Extend Cylinder,
"B" & "C" (Reservoir on Head end) CCW rotation
extends the cylinder. Orientation can be inverted
through keypad entry see page 21
C
CC
CW
W C
CM
MD
D ((iinnppuutt))
When True (High) drive will spin the pump in a
counterclockwise function. HAS Speed is set by the
V1setting on key pad setup, see Page 22 for details.
E
Enndd ooff S
Sttrrookkee LLiim
miitt S
Sw
wiittcchheess
If desired, end of stroke limit switches maybe used with
HAS Programmed Drives. Default setting is for
Normally Open type switches, Setting to Normally
Closed is done through Key Pad entry see page 25 for
more details
E
Exxtteenndd LLS
S ((IInnppuutt))
When True (High) drive will ramp HAS unit to a
stopped condition in extend motion only. Ramp time
value is set by keypad entry Page 26 for details. It is
recommended to remove CMD input when this
condition is seen.
P
Paarrkkeerr H
Haannnniiffiinn C
Coorrppoorraattiioonn
Cylinder Division
Des Plaines, Illinois
27
w
ww
ww
w..ppaarrkkeerr..ccoom
m/
cylinder
0011
0022
0033
0044
++2244 VV
0011
0022
0033
0044
0055
0066
0077
0088
0099
XX1144
XX1155
E
EN
NA
AB
BLLE
E
C
CW
W C
CM
MD
D
C
CC
CW
W C
CM
MD
D
E
EXXTTE
EN
ND
D LLS
S
R
RE
ETTR
RA
AC
CTT LLS
S
P
PR
RO
OFFIILLE
ER
R
R
RE
ES
S LLE
EVVE
ELL
C
CW
W LLIIM
MIITT
C
CC
CW
W LLIIM
MIITT
LL
LL
00 VV
FFA
AU
ULLTTE
ED
D
LL
Input Overview