manualshive.com logo in svg

Parker Bestobell Valves IOM 002, Installation, Operation And Maintenance Manual

Share
Download
Parker Bestobell Valves IOM 002 Installation, Operation And Maintenance Manual Download Page 11

 

Date of Issue: 19 August 2021 

Page 11 of 24 

QF 80: Issue 2 

Parker Hannifin 

– Instrumentation Products Division Europe  

President Park, President Way, Sheffield,  
South Yorkshire, S4 7UR, United Kingdom 
Tel: +44 (0) 114 224 0000   Web: www.parker.com/ipd 

 

 

Globe / Needle Valve (DN10 (⅜”) – DN50 (2”) 

 

Reference Number:

 

IOM 002 

Date: 

20 May 2014 

 

Issue: 

B 

Installation and Maintenance 

Spares Kit 

 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
Handwheel, separate gasket and full headwork are also available upon request. 

 

Please contact Bestobell Valves for specific part numbers 

Reference 

Description 

Spares Kit 

1 

Wiper Seal 

Contact 

Bestobell Valves 

Technical Sales 

2 

Chevron Top 

3 

‘O’ Seal 

2a 

Chevron Top 

4 

Chevron Bottom 

5 

Gasket 

6 

Valve Seal Flat 

7 

Anti-Friction Disc 

1 

2 

3 

2a 

4 

5 

6 

7 

Summary of Contents for Bestobell Valves IOM 002

























Reviews:

No comments

Brands by name

Popular brands

Load more brands