Parker AC30V Series, Product Manual

Page: 387 / 414

Parameter Reference
D-148
AC30V series Variable Speed Drive
PNO
Name Path(s) Type Default Range Units WQ View Notes MBus
1501 AR Trip Mask.29 INTERNAL FAN FAIL Same as PNO 1469 BOOL TRUE ALWAYS TECHNICIAN 03529
1502 AR Trip Mask.30 CURRENT SENSOR
Setup::Motor Control::Auto Restart
Parameters::Motor Control::Auto Restart
BOOL TRUE ALWAYS TECHNICIAN 03531
1503 AR Trip Mask.31 POWER LOSS STOP Same as PNO 1502 BOOL TRUE ALWAYS TECHNICIAN 03533
1505 AR Initial Delay Same as PNO 1502 TIME 10.000 0.000 to 3600.000 s ALWAYS OPERATOR 03537
1506 AR Repeat Delay Same as PNO 1502 TIME 60.000 0.000 to 3600.000 s ALWAYS OPERATOR 03539
1507 AR Active Parameters::Motor Control::Auto Restart BOOL NEVER OPERATOR 03541
1508 AR Restart Pending Parameters::Motor Control::Auto Restart BOOL NEVER OPERATOR 03543
1509 AR Restarts Remaining Parameters::Motor Control::Auto Restart USINT 0 to 20 NEVER OPERATOR 03545
1510 AR Time Remaining Parameters::Motor Control::Auto Restart TIME 0.000 to 3600.000 s NEVER OPERATOR 03547
1511 Encoder Supply
Setup::Inputs and Outputs::Option
Parameters::Option IO::Encoder
USINT
(enum)
0
0:5 V
1:12 V
2:15 V
3:24 V
STOPPED TECHNICIAN 03549
1512 Encoder Lines Same as PNO 1511 DINT 2048 1 to 100000 STOPPED TECHNICIAN 03551
1513 Encoder Invert Same as PNO 1511 BOOL FALSE STOPPED TECHNICIAN 03553
1514 Encoder Type Same as PNO 1511
USINT
(enum)
0
0:QUADRATURE
1:CLOCK/DIRECTION
STOPPED TECHNICIAN 03555
1515 Encoder Single Ended Same as PNO 1511 BOOL FALSE STOPPED TECHNICIAN 03557
1516 Encoder Speed
Monitor::Inputs and Outputs
Parameters::Option IO::Encoder
REAL x. Min to Max RPM NEVER OPERATOR 03559
1517 Encoder Count Reset Same as PNO 1511 BOOL FALSE ALWAYS TECHNICIAN 2 03561
1518 Encoder Count Same as PNO 1516 DINT -214783648 to 214783647 NEVER TECHNICIAN 03563
1520 Actual Rotor T Const Parameters::Motor Control::Tr Adaptation REAL x. 1 to 100000 ms NEVER ENGINEER 03567
1521 Tr Adaptation Output Parameters::Motor Control::Tr Adaptation REAL x. 1 to 500 % NEVER ENGINEER 03569
1526 Energy Saving Lower Lim Parameters::Motor Control::Fluxing VHz REAL 0.00 0.00 to 100.00 % ALWAYS OPERATOR 03579
1527 Max Available Volts Parameters::Motor Control::Tr Adaptation REAL x. 0 to 10000 V NEVER ENGINEER 03581
1528 Demanded Terminal Volts Parameters::Motor Control::Tr Adaptation REAL x. 0 to 1000 V NEVER ENGINEER 03583
1529 Terminal Volts Parameters::Motor Control::Tr Adaptation REAL x. 0 to 1000 V NEVER ENGINEER 03585
1533 Control Type
Setup::Motor Control::Control and Type
Parameters::Motor Control::Control Mode
USINT
(enum)
0
0:SENSORLESS
1:ENCODER FEEDBACK
STOPPED TECHNICIAN 6 03593
1534 Clone Filename
Setup::Clone
Parameters::Device Manager::Clone
STRING[24] clone ALWAYS TECHNICIAN 2 03595
1537 Clone Direction Same as PNO 1534
USINT
(enum)
0
0:SAVE TO FILE
1:LOAD FROM FILE
ALWAYS TECHNICIAN 2 03601
1538 Full Restore Same as PNO 1534
USINT
(enum)
0
0:YES
1:PARTIAL
ALWAYS TECHNICIAN 2 03603
1539 Application Same as PNO 1534
USINT
(enum)
0
0:LOAD FROM FILE
1:LEAVE CURRENT APP
ALWAYS TECHNICIAN 2 03605
1540 Other Parameters Same as PNO 1534
USINT
(enum)
0
0:LOAD FROM FILE
1:LEAVE CURRENT VALUES
2:SET TO DEFAULT VALUES
ALWAYS TECHNICIAN 2 03607
1541 Power Parameters Same as PNO 1534
USINT
(enum)
0 Same as PNO 1540 ALWAYS TECHNICIAN 2 03609
1542 Clone Start Same as PNO 1534 BOOL FALSE ALWAYS TECHNICIAN 2 03611
1543 Clone Status Same as PNO 1534
USINT
(enum)
0:IDLE
1:SAVING
2:RESTORING
3:VERIFYING
4:DONE
5:CANNOT START
6:FAILED
7:NO SD CARD
8:VERIFY FAILED
9:FILE NOT OPENED
10:FILE INCOMPATIBLE
11:FILE FAILURE
12:POWER MISMATCH
13:APPLICATION FAILURE
14:PARAMETERS FAILURE
NEVER TECHNICIAN 03613
1544 Filter Type Parameters::Motor Control::Filter On Torque Dmd
USINT
(enum)
0
0:NONE
1:MAX ATTENUATION
2:MINIMUM PHASE
3:PHASE ADVANCE
4:NOTCH
ALWAYS TECHNICIAN 03615
1545 Cut Off Frequency Parameters::Motor Control::Filter On Torque Dmd REAL 2000 20 to 6000 Hz ALWAYS TECHNICIAN 03617