background image

                     

OPERATING INSTRUCTIONS

                               

     Bulletin

 

                                              

MODEL DA1500DR

                                   

       

262-1500-2-DR

 

                                     

MAGNETIC INSPECTION UNIT

          

          

July 2015

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 
 
 

 

 

 

 

 

 

 

 

   

  

 

 
 

THE CONTENTS OF THIS MANUAL MUST BE READ AND FULLY UNDERSTOOD 

BEFORE INSTALLATION, OPERATION OR MAINTENANCE OF THIS EQUIPMENT. 

FAILURE TO DO SO MAY RESULT IN INJURY. 

 
 
                

 

   

      

INTRODUCTION 

 
 

The DA1500DR Magnetic Inspection Unit is a portable power pack designed to furnish high 
amperage, low voltage AC current and Half-Wave rectified (DC) current for Magnetic Particle 
inspection. It features infinitely variable magnetizing and demagnetizing current. 

 
 

          

 THE FOLLOWING SHOULD BE READ AND FULLY UNDERSTOOD.  

 
 

 

 

  

SAFETY PRECAUTIONS   

 

PAGE 2 

 

 

 

GENERAL DESCRIPTION  

 

PAGE 2 

 

 

 

ELECTRICAL FEATURES  

 

PAGE 3 

 

 

 

CONNECTION 

 

 

 

PAGE 3 

 

 

 

CONTROLS-ELECTRICAL 

 

PAGE 4 

 

 

 

OPERATION  

 

 

 

PAGE 5 

 

 

 

SERVICE DATA & WARRANTY   

PAGE 6 

 

 

 

 

 

SCHEMATIC DIAGRAM   

 

PAGE 7-8 

 
 
Parker Research Corporation assumes no liability from any claims arising from the use of this 
equipment. 
 

CAUTION:

 For the correct and safe use of this equipment, proper training of operating 

personnel to required inspection techniques, specifications and safety requirements is 
necessary and is the obligation of the user. 
 
 
 

 

 

 

 

   

 

 

 

      

 
 
 
 

 

 

 

 

Summary of Contents for DA1500DR









Reviews: