background image

2

Software and Firmware License Agreement 

The terms and conditions of this License Agreement (the “Agreement”) will apply to the 
software and/or firmware (individually or collectively the “Software”) incorporated into 
the Paradyne product (the “Product”) purchased by you and any derivatives obtained 
from the Software, including any copy of either. If you have executed a separate written 
agreement covering the Software supplied to you under this purchase, such separate 
written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept 
a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use 
the Software, solely as it is intended and solely as incorporated in the Product 
purchased from Paradyne or its authorized distributor or reseller under the following 
terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The 

Licensee acquires no title, right or interest in the Software other than the license 
granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in which 

the Product was rightfully purchased except upon prior written notice to Paradyne 
and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the Software in 

whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.

Summary of Contents for Hotwire ReachDSL 6350-A4





















Reviews: