background image

1

Hotwire

®

 ADSL/R Bridge/Router, Model 6381

with Inline Phone Filter

Installation Instructions

Document Number 6381-A2-GN10-10

April 2003

Installation Procedures

To install the Hotwire ADSL/R Bridge/Router:

Verify the contents of the package and obtain the correct cables (see 

Package 

Checklist

 on page 2 and 

Wiring and Cables You Need (not supplied)

 on page 2)

Install phone filters on all phones that will share the same phone line as the router 
(see 

Installing Phone Filters

 on page 3)

Connect the router (see 

Installing the Hotwire ADSL/R Bridge/Router

 on page 4)

Verify that the front panel LEDs show the correct status (see 

LED Status

 on page 7)

If necessary, configure the router (see 

Configuring the Hotwire ADSL/R 

Bridge/Router

 on page 8)

Definitions

The following terms are used in this booklet.  

network

A group of connected things, such as telephones or computers.

bridge

A device that forwards any message from one part of a network to 
another. The Hotwire ADSL/R Bridge/Router is shipped as a bridge. 

router

A device that forwards messages according to their network 
addresses. You must configure the Hotwire ADSL/R Bridge/Router to 
make it work as a router.

POTS

Plain Old Telephone Service. The voice service provided over the 
public switched telephone network (PSTN).

DSL

Digital Subscriber Line. The technology that allows you to use a POTS 
line for both voice calls and high-speed Internet access 
simultaneously.

ADSL

Asymmetric DSL. A version of DSL that allows a higher speed for 
information coming from the Internet to your PC (“downstream”) than 
it does for information going to the Internet from your PC (“upstream”).

ReachDSL

A proprietary Paradyne version of DSL that works on lines too long or 
too noisy for ADSL.

ADSL/R

The technology that combines ADSL and ReachDSL in one device. 

Summary of Contents for Hotwire 6381





















Reviews: